OpenMarine

Last year i successfully installed op in my boat. It gives me a optimum support during my navigation in the north adriac see.
Now i would like to implement my configuration connecting my autohelm to op, basically for the batimetric and wind misure.
I have the instrument panel and the plug as show below... Sameone can explain in a simple way how can i connect them to op?
Thank you for all your help and support



Inviato dal mio ANE-LX2 utilizzando Tapatalk

Unfortunately ST50 TRIDATA and ST50 Wind instrument has no NMEA 0183 interface for connecting third party equipment (only ST50+ TRIDATA REPEATER and Autohelm MFD has it).
Tridata and Wind displays only has Seatalk interface (3pin connector on your picture)

You need some kind of Seatalk->NMEA 0183 converter, for example Raymarine "PC/Seatalk/NMEA Interface BOX" (some call it RS232 BOX) which is hard to find and not so cheap (for my taste)

---

PS: I see second seatalk cable on your picture (from wind instrument) which is leading to some another place. It is just power or i guess you have at least one another device in your seatalk network. What is it? Is it Repeater?

Thank you.
This one can make the work? https://www.painestore.it/convertitore_s...vMEALw_wcB

Something cheaper exists?



I though it was 1 camble for wind and 1 for depth... But i never check. Next time i will

Inviato dal mio ANE-LX2 utilizzando Tapatalk

That device is for Seatalk NG. The instruments you showed use first generation Seatalk. You need a two way Seatalk bridge.

Sent from my CLT-L04 using Tapatalk

(2020-02-23, 12:11 PM)luchin0 Wrote: [ -> ]Thank you.
This one can make the work? https://www.painestore.it/convertitore_s...vMEALw_wcB

Something cheaper exists?



I though it was 1 camble for wind and 1 for depth... But i never check. Next time i will

Inviato dal mio ANE-LX2 utilizzando Tapatalk

Hi, you should use this. It's also cheap ... good wind! 
Http: //yakbitz.com/ST1toNMEA.aspx

Thank you for your suggestion.

How i connect it to my rpi with moittesier hat?

Difference with this one?
https://www.ebay.it/itm/SEAYAK-Seatalk1-...3224200076

Inviato dal mio ANE-LX2 utilizzando Tapatalk

(2020-02-23, 04:49 PM)luchin0 Wrote: [ -> ]Thank you for your suggestion.

How i connect it to my rpi with moittesier hat?

Difference with this one?
https://www.ebay.it/itm/SEAYAK-Seatalk1-...3224200076

Inviato dal mio ANE-LX2 utilizzando Tapatalk

Hi, it's the same I indicated. It comes from Australia (it will take some time, but the seller is serious). You must connect the output of your instruments (identifying the three corresponding colors: red + black mass or gnd- yellow Seatalk data) to the "Seyak" and connect it with the cable in dodation to a USB port of the rpi. Good job 

Is that device bi-directional?

(2020-02-23, 10:39 PM)Techstyle Wrote: [ -> ]Is that device bi-directional?

No.!

(2020-02-24, 10:26 AM)Max1947 Wrote: [ -> ]

(2020-02-23, 10:39 PM)Techstyle Wrote: [ -> ]Is that device bi-directional?

No.!

Full dupplex with conversion all navi standard ( nmea183, NMEA2000 and SeaTalk) are this
https://ocenav.com/en/home/
That's the one I have on my boat. I have the same ST50 system

Gesendet von meinem CLT-L29 mit Tapatalk