OpenMarine
Compatible multiplexers list - Printable Version

+- OpenMarine (http://forum.openmarine.net)
+-- Forum: OpenPlotter (http://forum.openmarine.net/forumdisplay.php?fid=1)
+--- Forum: How do I...? (http://forum.openmarine.net/forumdisplay.php?fid=3)
+--- Thread: Compatible multiplexers list (/showthread.php?tid=109)



Compatible multiplexers list - Sailoog - 05-20-2016

Post here models and settings and we will add them to the list.
  • ShipModul MiniPlex-42USB. Settings: baudrate 57600.
  • ShipModul MiniPlex-3USB. Settings: baudrate 460800.
  • www.gadgetpool.de SeaTalk NMEA Bridge128SD. Settings: baudrate 38400
  • The Brookhouse line of multiplexers work great. http://www.brookhouseonline.com



RE: Compatible multiplexers list - gilinas - 01-22-2017

(05-20-2016, 08:37 AM)Sailoog Wrote: Post here models and settings and we will add them to the list.
  • ShipModul MiniPlex-42USB. Settings: baudrate 57600.



RE: Compatible multiplexers list - JeroenAdam - 06-10-2017

ShipModul MiniPlex-3USB
I added the multiplexer as a new device ttyOP_1 using USB manager and I added a NMEA 0183 serial input on port /dev/ttyOP_1 with 57600 bauds
No NMEA data stream in OpenCPN
**UPDATE** MiniPlex-3USB runs on 460800 baud
**UPDATE** Fixed with -> sudo stty -F /dev/ttyUSB0 460800


RE: Compatible multiplexers list - Sailoog - 06-13-2017

(06-10-2017, 12:06 PM)JeroenAdam Wrote: ShipModul MiniPlex-3USB
I added the multiplexer as a new device ttyOP_1 using USB manager and I added a NMEA 0183 serial input on port /dev/ttyOP_1 with 57600 bauds
No NMEA data stream in OpenCPN
**UPDATE** MiniPlex-3USB runs on 460800 baud
**UPDATE** Fixed with -> sudo stty -F /dev/ttyUSB0 460800

thanks!


RE: Compatible multiplexers list - MilesAhead - 08-14-2018

I'm trying to configure a DTech serial to USB converter to pick up the NMEA 0183 signals from a Raymarine SmartPilot. See page 4 in the commissioning manual. I have an S1.

My issue is that I do not see the "USB Manager", "NMEA 0183", or "NMEA 2K" tabs as described in the OpenPlotter documentation. All I see is a "Serial" tab, followed by the "Signal K" tab. 

Is there a configuration setting? Have I installed the incorrect version of OP?

(08-14-2018, 05:55 AM)MilesAhead Wrote: I'm trying to configure a DTech serial to USB converter to pick up the NMEA 0183 signals from a Raymarine SmartPilot. See page 4 in the commissioning manual. I have an S1.

My issue is that I do not see the "USB Manager", "NMEA 0183", or "NMEA 2K" tabs as described in the OpenPlotter documentation. All I see is a "Serial" tab, followed by the "Signal K" tab. 

Is there a configuration setting? Have I installed the incorrect version of OP?

BTW, I have a RPi 3 with the latest raspbian and I installed the latest NOOB version of OP/OpenCPN, then I updated OP & OpenCPN using OP.


RE: Compatible multiplexers list - Thomas_Reinhold - 08-24-2018

(05-20-2016, 08:37 AM)Sailoog Wrote: Post here models and settings and we will add them to the list.
  • ShipModul MiniPlex-42USB. Settings: baudrate 57600.
  • ShipModul MiniPlex-3USB. Settings: baudrate 460800.
  • www.gadgetpool.de SeaTalk NMEA Bridge128SD. Settings: baudrate 38400

shipmodul miniplex-2wi Setting: Baudrate 115200


RE: Compatible multiplexers list - RedRyder - 10-10-2018

The Brookhouse line of multiplexers work great.

I have an iMux which works perfectly.

http://www.brookhouseonline.com/


RE: Compatible multiplexers list - Bojayne@yahoo.com - 11-10-2018

(06-13-2017, 12:32 PM)Sailoog Wrote:
(06-10-2017, 12:06 PM)JeroenAdam Wrote: ShipModul MiniPlex-3USB
I added the multiplexer as a new device ttyOP_1 using USB manager and I added a NMEA 0183 serial input on port /dev/ttyOP_1 with 57600 bauds
No NMEA data stream in OpenCPN
**UPDATE** MiniPlex-3USB runs on 460800 baud
**UPDATE** Fixed with -> sudo stty -F /dev/ttyUSB0 460800

thanks!
I have a shipmodule Multiplexor with blue tooth.  Can this be added via bluetooth