Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 (/showthread.php?tid=1090) |
RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - 1jollymon - 2018-05-10 (2018-05-10, 10:47 PM)jim321 Wrote: thats the first mention of stretch in the post sorry for the confusion No Problem . . . I thought it was assumed. RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - 1jollymon - 2018-05-12 (2018-05-10, 06:48 PM)baltika_no_9 Wrote:(2018-05-10, 06:32 PM)1jollymon Wrote: Lesson learned . . . do not upgrade to 0.17.0. Stable because it contains Jessie and will not work on RPI B+. RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - Henryl - 2018-05-14 Hi, thanks for your suggestions, it works to get started Openplotter on Raspberry Pi 3, But no wifi , the IC2 modules are not found either. nor usb-SDR. but the usb-gps works. But no way the Raspberry Pi 3B+ system works, I can install it on pi3B+ with your suggestions, but when the system restarts, it hangs with a yellow flash. Have don the update on the pi3, still dos not work on the 3B+ Someone who wants to buy a new Raspberry Pi 3B + RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - baltika_no_9 - 2018-05-14 (2018-05-14, 04:00 PM)Henryl Wrote: Hi, thanks for your suggestions, it works to get started Openplotter on Raspberry Pi 3, Sorry to hear that but I have followed the process as I described three times now and it works perfectly fine on the 3B+. Others have done it too. RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - 1jollymon - 2018-05-14 (2018-05-14, 05:22 PM)baltika_no_9 Wrote:(2018-05-14, 04:00 PM)Henryl Wrote: Hi, thanks for your suggestions, it works to get started Openplotter on Raspberry Pi 3, I followed the steps provided above. I had to first download the latest Stretch NOOBS and unzipped it on my PC, then downloaded the OP 0.10.0 NOOBS onto my PC. Then as described, I merged the Openplotter file in the OP file to the Stretch NOOBS folder. I made a new micro SD and copied & Pasted onto the new SD. I placed it in a model B and booted. After that, I did all the updates in Openplotter update tab (i.e. 0.17.1). I then opened a terminal and did a "sudo apt-get update," and then a "sudo apt-get upgrade," and finally a "sudo rpi-update" which was probably wasn't needed. When everything was done, I moved the SD to my B+ and it booted, although I did not have WiFi or Bluetooth. I then had to follow the steps at this site, provided by Chris, https://raspberrypi.stackexchange.com/qu...2327#82327 and just like that . . . I had WiFi. I do suggest you are plugged into an ethernet to a router for internet connection to do all of this. It was frustrating but, I got it done. I am using a breakout board from SparkFun Qwiic Pi Hat for I2C https://www.sparkfun.com/products/14459, which is plug an play. Recommendation; also order (5 or 6) https://www.sparkfun.com/products/14425 to connect your I2C boards to the Hat. I'm using the following boards for I2C: BMP280 Temp/Pressure/Hum MPU9150 IMU My rtl_sdr does not show up anywhere except in the tuner and you need a very good antenna. Mine works and I'm getting targets but, it's still a mystery to me as to how it works. Hope this works for you. Chris RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - Henryl - 2018-05-15 I got it to work !!! Thank you very much för all u help. Henryl [/quote] RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - 1jollymon - 2018-05-16 (2018-05-15, 02:27 AM)Henryl Wrote: I got it to work !!![/quote] I'm glad I could help. Chris RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - manitu - 2018-05-16 I just got a raspberry pie 3+ but my old one is a 2B , not a 3B. Will the procedure work for me too? I can off course just try it , but I'll have to get another sd card, so.. Would be nice to know if it should work the same before wasting the whole night trying. .manitu RE: Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - baltika_no_9 - 2018-05-17 I can see no reason why it would not work. It does not depend on any intrinsic feature of a 3B, it simply needs a Pi that is NOT a 3B+. Good luck. Chris Intall OpenPlotter RPI v0.10.0 NOOBS on Pi3 - zedoc - 2018-05-18 Hi, I only have a mac and pc...and a virtual debian Can i make a bootable openplotter for my brand new 3B+ without having To buy an older pi? Envoyé de mon unknown en utilisant Tapatalk |