no imu data after update - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: Bug Reports (https://forum.openmarine.net/forumdisplay.php?fid=4) +--- Thread: no imu data after update (/showthread.php?tid=1340) |
no imu data after update - kalle - 2018-07-24 After update to 1.1.0 I have no more imu data when selcting "basic autopilot". When I select " imu only" I get heading. I already reinstalled the whole system. In version 1.0.0 it is workink but same behviour after update. RE: no imu data after update - Sailoog - 2018-07-24 Do you have a pypilot controller connected? You should only select basic autopilot if you are using pypilot RE: no imu data after update - kalle - 2018-07-24 (2018-07-24, 05:47 PM)Sailoog Wrote: Controller (arduino) is connected and was working before update. In version 1.0.0 everything is ok, but afterwards not working. If I choose "basic autopilot" even selection of pitch and roll are not possible and greyed out. RE: no imu data after update - It Paradyske - 2018-07-25 (2018-07-24, 11:01 PM)kalle Wrote:(2018-07-24, 05:47 PM)Sailoog Wrote: Controller (arduino) is connected and was working before update. In version 1.0.0 everything is ok, but afterwards not working. If I choose "basic autopilot" even selection of pitch and roll are not possible and greyed out. Same here, upgrade from 1.0.0 to 1.1.0. IMU not functioning anymore. MPU-9250/9255 is still detected, but values for tillt heading pitch etc. are all "n/a". Went back to 1.0.0, and it worked again. Regards Hans Fix RE: no imu data after update - Sailoog - 2018-07-25 Please check if you have any error output. open a terminal and type openplotter. Go to pypilot tab, press restart and watch the terminal. RE: no imu data after update - kalle - 2018-07-25 (2018-07-25, 06:28 PM)Sailoog Wrote: Please check if you have any error output.I have attached the debug output when restarting pypilot in autopilot mode. There seems to be something wrong. As I am not a programmer (only a little bit arduino) I do not know what . For the moment I can also go back to OP 1.0.0 but it would be nice if the problem could be solved for the future. RE: no imu data after update - Sailoog - 2018-07-26 Thanks. Please follow this post where we are fixing this: http://forum.openmarine.net/showthread.php?tid=1314&pid=6485#pid6485 RE: no imu data after update - kalle - 2018-07-29 (2018-07-26, 06:20 PM)Sailoog Wrote: Thanks. It is working now. Thank you. RE: no imu data after update - sapers - 2018-08-16 (2018-07-25, 06:08 AM)It Paradyske Wrote:confirm this situation. 1.1.0 version has some errors such this one. Also NMEA generator doesn't works correctly, I can't to edit existing sentecies and add some sentencies, for example ROT, HDT e.t.c.(2018-07-24, 11:01 PM)kalle Wrote:(2018-07-24, 05:47 PM)Sailoog Wrote: Controller (arduino) is connected and was working before update. In version 1.0.0 everything is ok, but afterwards not working. If I choose "basic autopilot" even selection of pitch and roll are not possible and greyed out. |