Moitessier HAT 2 roadmap - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Moitessier HAT 2 roadmap (/showthread.php?tid=2152) |
RE: Moitessier HAT 2 roadmap - Sailoog - 2020-01-11 You have an old driver installed, your hat will not work until you install the right one in a terminal type lsmod and send me the output copy here contents of /boot/config.txt file too I am afraid MCS app is doing something unusual. Uninstall MCS and try again. RE: Moitessier HAT 2 roadmap - Max1947 - 2020-01-12 (2020-01-11, 09:16 PM)Sailoog Wrote: You have an old driver installed, your hat will not work until you install the right one Hi Sailoog, after the update to 2.0.22, both the rasp3 and the 4 have crashed. Tomorrow I'll try again ... ("in an lsmod terminal and don't send me the output copy here of the content of the file /boot/config.txt ") is too technical for me ... if you explain me how and what to do, I am attaching everything you want. Good night and good job! RE: Moitessier HAT 2 roadmap - Sailoog - 2020-01-12 What you should test: - Uninstall MCS and try to get moitessier hat working. You can use a fresh openplotter pre-release image. - After having the hat working install MCS app and lets see what happens - If it does not work, copy here the contents of the file /boot/config.txt RE: Moitessier HAT 2 roadmap - Max1947 - 2020-01-12 (2020-01-12, 11:53 AM)Sailoog Wrote: What you should test: Ok, I'm working on it, I'll let you know, bye. RE: Moitessier HAT 2 roadmap - Max1947 - 2020-01-12 (2020-01-12, 11:53 AM)Sailoog Wrote: What you should test: Hi Sailoog, I tried as you say. Everything ok without the MCS card. As I put it all on the MCS returns the warning in red of the SPI- So I assume that the conflict is with the MCS card. Here is "config.txt". A nice mess! You don't have MCS and Glowntiger is waiting for the new Moitessier cap ... hopefully you can solve it! # For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output #hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces dtparam=i2c_arm=on #dtparam=i2s=on dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on [pi4] # Enable DRM VC4 V3D driver on top of the dispmanx display stack dtoverlay=vc4-fkms-v3d max_framebuffers=2 [all] #dtoverlay=vc4-fkms-v3d enable_uart=1 gpu_mem=100 dtoverlay=i2c-gpio,i2c_gpio_sda=2,i2c_gpio_scl=3,bus=3 #MCS-Openplotter config (Do not delete or edit this part)(start) dtoverlay=sc16is752-i2c,int_pin=13,addr=0x4c,xtal=14745600 dtoverlay=sc16is752-i2c,int_pin=12,addr=0x49,xtal=14745600 dtoverlay=sc16is752-i2c,int_pin=6,addr=0x48,xtal=14745600 #MCS-Openplotter config (Do not delete or edit this part)(end) dtoverlay=mcp2515-can1,oscillator=16000000,interrupt=25 dtoverlay=w1-gpio RE: Moitessier HAT 2 roadmap - glowntiger - 2020-01-13 Hi, I do not know how the SPI driver for the Moitessier works. The MCS uses SPI CE1. Moitessier CE0 so it should no problem.... I have tested yesterday the MCS with a second device on CE0 and all works. Can you tap Code: ls /dev/ and make a screenshot? When an Moitessier hat is availible I buy one and can test it by my own.... So not to spam this thread I have make this: http://forum.openmarine.net/showthread.php?tid=2233 RE: Moitessier HAT 2 roadmap - Max1947 - 2020-01-13 (2020-01-13, 08:46 AM)glowntiger Wrote: Hi, Ecco: pi@openplotter:~ $ ls /dev/ argon-h264mem loop6 rpivid-intcmem tty36 ttySC5 argon-hevcmem loop7 rpivid-vp9mem tty37 uhid argon-intcmem loop-control sda tty38 uinput argon-vp9mem mapper sda1 tty39 urandom autofs media0 serial0 tty4 usb block mem serial1 tty40 v4l bsg memory_bandwidth sg0 tty41 vchiq btrfs-control mmcblk0 shm tty42 vcio bus mmcblk0p1 snd tty43 vc-mem cachefiles mmcblk0p2 stderr tty44 vcs char moitessier.ctrl stdin tty45 vcs1 console moitessier.spi stdout tty46 vcs2 cpu_dma_latency moitessier.tty tty tty47 vcs3 cuse mqueue tty0 tty48 vcs4 disk net tty1 tty49 vcs5 dri network_latency tty10 tty5 vcs6 fb0 network_throughput tty11 tty50 vcs7 fd null tty12 tty51 vcsa full port tty13 tty52 vcsa1 fuse ppp tty14 tty53 vcsa2 gpiochip0 ptmx tty15 tty54 vcsa3 gpiochip1 pts tty16 tty55 vcsa4 gpiochip2 ram0 tty17 tty56 vcsa5 gpiochip3 ram1 tty18 tty57 vcsa6 gpiochip4 ram10 tty19 tty58 vcsa7 gpiochip5 ram11 tty2 tty59 vcsm gpiomem ram12 tty20 tty6 vcsm-cma hidraw0 ram13 tty21 tty60 vcsu hidraw1 ram14 tty22 tty61 vcsu1 hidraw2 ram15 tty23 tty62 vcsu2 hwrng ram2 tty24 tty63 vcsu3 i2c-1 ram3 tty25 tty7 vcsu4 i2c-3 ram4 tty26 tty8 vcsu5 initctl ram5 tty27 tty9 vcsu6 input ram6 tty28 ttyAMA0 vcsu7 kmsg ram7 tty29 ttyOP_moitess vga_arbiter log ram8 tty3 ttyprintk vhci loop0 ram9 tty30 ttyS0 video10 loop1 random tty31 ttySC0 video11 loop2 raw tty32 ttySC1 video12 loop3 rfkill tty33 ttySC2 watchdog loop4 rpivid-h264mem tty34 ttySC3 watchdog0 loop5 rpivid-hevcmem tty35 ttySC4 zero pi@openplotter:~ $ (2020-01-13, 11:14 AM)Max1947 Wrote:(2020-01-13, 08:46 AM)glowntiger Wrote: Hi, [img][/img] RE: Moitessier HAT 2 roadmap - Sailoog - 2020-01-13 The new Moitessier HAT 2 will be back in stock on 17th January 2020. Back orders are allowed. RE: Moitessier HAT 2 roadmap - glowntiger - 2020-01-13 Hi Sailoog, is the firmware availible for checking? I think the fw blocks the complete SPI?? RE: Moitessier HAT 2 roadmap - Sailoog - 2020-01-13 sure, but I do not think so: https://github.com/mr-rooney/moitessier/ I have some hypothesis I will post tomorrow here: http://forum.openmarine.net/showthread.php?tid=2233 |