i2c without Mointessier hat - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: i2c without Mointessier hat (/showthread.php?tid=2369) |
i2c without Mointessier hat - carlos-palma - 2020-02-24 Hi all, Thanks for the effort with this excellent app. My problem is how to read pressure and temperature from my imu to put the data in signal k. Actually I get heading, heel and pitch from pypilot, but as data for pressure and temperature is not used by pypilot, is not read and is not send to signal k. I have the app i2c but when executed nothing happens, nothing opens. All the rest, ais and gps are serial and work OK. Thanks and regards, Carlos. RE: i2c without Mointessier hat - Sailoog - 2020-02-24 What is the model of your pressure, temperature sensor? what means "nothing happens" when you open I2C? RE: i2c without Mointessier hat - carlos-palma - 2020-02-25 (2020-02-24, 04:06 PM)Sailoog Wrote: What is the model of your pressure, temperature sensor?Thanks for your answer! My imu is reported by pypilot as: Invensense MPU-9250/MPU-9255, the printed circuit reads MPU-92.65 It was working fine with openplotter older versions. When I click I2C I was expecting to open a window to see the detected sensors, calibration, etc, but nothing opens. I can see the clock as doing something but after a few seconds it is over with no visible result. I did un-install and re-install I2C twice with no results. Thanks for your help, Carlos. (2020-02-24, 04:06 PM)Sailoog Wrote: What is the model of your pressure, temperature sensor?Thanks for your answer! My imu is reported by pypilot as: Invensense MPU-9250/MPU-9255, the printed circuit reads MPU-92.65 It was working fine with openplotter older versions. When I click I2C I was expecting to open a window to see the detected sensors, calibration, etc, but nothing opens. I can see the clock as doing something but after a few seconds it is over with no visible result. I did un-install and re-install I2C twice with no results. Thanks for your help, Carlos. RE: i2c without Mointessier hat - Sailoog - 2020-02-25 Edit /home/pi/.openplotter/openplotter.conf and remove everything under the tag [I2C] That is your IMU but what is your pressure sensor? check the detected addresses when you can open the I2C app RE: i2c without Mointessier hat - carlos-palma - 2020-02-25 (2020-02-25, 07:21 PM)Sailoog Wrote: Edit /home/pi/.openplotter/openplotter.conf and remove everything under the tag [I2C] Thanks, now I2C works and detects the pressure, temperature and humidity as BME280 0/1/2. The pressure is displayed by Open CPN but not the air temperature, will keep checking. Thanks, that was the problem!! (2020-02-25, 07:42 PM)carlos-palma Wrote:(2020-02-25, 07:21 PM)Sailoog Wrote: Edit /home/pi/.openplotter/openplotter.conf and remove everything under the tag [I2C] RE: i2c without Mointessier hat - klr68 - 2020-05-23 (2020-02-25, 07:42 PM)carlos-palma Wrote:(2020-02-25, 07:21 PM)Sailoog Wrote: Edit /home/pi/.openplotter/openplotter.conf and remove everything under the tag [I2C] Hi! Change Signal K Key "environment.inside.temperature" to the key "environment.outside.temperature" select line 1 BME280 > then Edit button In the new box select Edit button in the new box select in 'group' > "environment" ,in 'Keys' "outside.temperature" >OK to go back >OK to go back Carole RE: i2c without Mointessier hat - carlos-palma - 2020-05-24 (2020-05-23, 02:21 PM)klr68 Wrote:(2020-02-25, 07:42 PM)carlos-palma Wrote:(2020-02-25, 07:21 PM)Sailoog Wrote: Edit /home/pi/.openplotter/openplotter.conf and remove everything under the tag [I2C] Thanks Carole, that made it work!! Best, Carlos. |