Problems with NMEA out to VHF radio in OP V2. - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: Problems with NMEA out to VHF radio in OP V2. (/showthread.php?tid=2419) |
RE: Problems with NMEA out to VHF radio in OP V2. - Celestine - 2020-03-30 (2020-03-19, 08:10 AM)Albin Wrote:Hi(2020-03-18, 09:56 PM)Celestine Wrote:(2020-03-11, 08:38 AM)Albin Wrote:Hi,(2020-03-10, 08:04 PM)emilecantin Wrote: I assume you were using kplex in OP1? I use usb0 with an usb-serial converter. The pi sees the Profilic port and I have configured just like you (apart from the port name) but no output on port. Ocpn is sending a nice 0183 stream in the udp port. Don’t understand this... /pw RE: Problems with NMEA out to VHF radio in OP V2. - Celestine - 2020-04-06 Hi, In order to be able to troubleshoot this at all I have stripped my setup down do minimal. All the nmea2000 devices are disconnected. All that is left is an old Garmin GPS 76 (handy because it has a built in nmea simulator) that delivers nmea0183 sentences to OpenPlotter via a Profilic Serial to USB converter. Output is sent to a Garmin GNX20 with only the nmea0183 port connected to OpenPlotter via another Profilic converter. I use the named nmea0183 gps in this test and have disconnected all other nmea2000 devices to make sure that the only data that reach the GNX20 comes from OP and are not leaked from the can bus one way or another Settings are as follows: GPS Connected to ttyUSB0 Alias: ttyOP_gps Connection: SignalK Baudrate: 4800. I can see sentences flowing in to Data Browser just as expected. GNX20 display Connected to ttyOP_ap Connection: SignalK Baudrate: 4800 Output event: nmea0183,nmea0183out Sentence event: nmea1data. No data is shown neither on the GNX20 nor in Data Browser. I know all the hardware is working because if I keep the same physical connections but route the signals directly to OCPN (both input and output) I see data flowing in and out in the diag window of OCPN. Data is also shown on the GNX20. What am I doing wrong here? How can I make OP send data out on a USB port? Running on RPI3 with OP2 Serial 2.1.0, SignalK 1.26.0, SignalK-to-nmea0183 1.6.1 RE: Problems with NMEA out to VHF radio in OP V2. - emilecantin - 2020-04-06 (2020-04-06, 09:49 PM)Celestine Wrote: Hi, Try adding a sentenceEvent (can be whatever name you want, but just one word) to your GPS connection in SignalK. Then, on your GNX20 connection, use that same name as the Output Event. You should be able to see some data on your GNX20 display after that. Don't forget to save & restart your server. RE: Problems with NMEA out to VHF radio in OP V2. - e-sailing - 2020-04-07 Have you read https://openplotter.readthedocs.io/en/latest/signalk/signalk_nmea0183_multiplexing.html? RE: Problems with NMEA out to VHF radio in OP V2. - Celestine - 2020-04-07 (2020-04-07, 02:48 PM)e-sailing Wrote: Have you read https://openplotter.readthedocs.io/en/latest/signalk/signalk_nmea0183_multiplexing.html? Hi, That’s very interesting information! I will check that out as well. I’m sure I checked the docs pages the other week. These must be quite new? Will get back with a report as soon as I tested all suggestions. Cheers Pär W RE: Problems with NMEA out to VHF radio in OP V2. - emilecantin - 2020-04-07 (2020-04-07, 06:50 PM)Celestine Wrote:(2020-04-07, 02:48 PM)e-sailing Wrote: Have you read https://openplotter.readthedocs.io/en/latest/signalk/signalk_nmea0183_multiplexing.html? Github says 12 days, so yes, quite new. RE: Problems with NMEA out to VHF radio in OP V2. - Celestine - 2020-04-28 (2020-04-07, 06:50 PM)Celestine Wrote:(2020-04-07, 02:48 PM)e-sailing Wrote: Have you read https://openplotter.readthedocs.io/en/latest/signalk/signalk_nmea0183_multiplexing.html? Hi, Followed the instructions in https://openplotter.readthedocs.io/en/latest/signalk/signalk_nmea0183_multiplexing.html? Worked like a charm! Thanks a lot, Pär W RE: Problems with NMEA out to VHF radio in OP V2. - Seacat - 2020-05-17 Hello, Pls advice what can be wrong with following or how to check data flow: I am trying to send AIS data from Openplotter SDR AIS to Chartplotter Garmin GPSmap620, have tried both ways Signal K to Nmea0183 and NMEA0183 to NMEA0183 plugins without success. RPi4, Signal K 1.29., Openplotter SDR AIS 2.1.0 (Works well), Garmin is connected via usb-serial ch340 (USB to RS485) nmea0183 to nmea0183 settings in Signal K was SDR AIS: Input type NMEA0183 ID Openplotter SDR AIS NMEA0183 Source UDP port 8080 SentenceEvent nmea1data Garmin at usb-serial Input type NMEA0183 ID aisout NMEA0183 Source Serial Serial port /dev/ttyOP_aisout baudrate 38400 OutputEvents aisout SentenceEvent 'empty' Plugin NMEA0183 - NMEA0813 Active Input event nmea1data Output event aisout NMEA0183 Sentences VDM, VDO (have tried to send also all available sentences) Also have tried for Signal K to NMEA0183 to put in USB-Serial OutputEvents nmea0183 or nmea0183out or nmea1data, but with success. After any correction in settings Signal K was restarted. After all Signal K dashboard still shows no Connection Activity for aisout. RE: Problems with NMEA out to VHF radio in OP V2. - sapers - 2020-05-18 My idea is using AisReporter plugin for transmit my AI VDO (or VDM) sentencies for VHF (as AIS transponder). It is possible? RE: Problems with NMEA out to VHF radio in OP V2. - Seacat - 2020-05-24 (2020-05-18, 08:33 PM)sapers Wrote: My idea is using AisReporter plugin for transmit my AI VDO (or VDM) sentencies for VHF (as AIS transponder). It is possible? AirReporter is for "Signal K Node server plugin to report the vessel's AIS data to MarineTraffic" But I need to route AIS data received by Openplotter SDR AIS to USB-Serial device. |