Maiana AIS has stopped - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Maiana AIS has stopped (/showthread.php?tid=5074) Pages:
1
2
|
Maiana AIS has stopped - Lazzz - 2023-12-30 I've had my Maiana AIS USB + RS422 Adapter since Dec 2021 & it has been working flawlessly these past two years. All of a sudden, for no apparent reason, it just stopped transmitting & receiving. The power light is on but the GPS, RX & TX lights are not!! I removed the CAT 5 cable & sprayed the connections & when I re-inserted the cable there was a feint glimmer on the lights but then went off again. Has anyone any ideas where to start looking for problems or how to test?? I can't tell whether it's the main PCBA in the aerial or in the USB + RS422 Adapter. TIA RE: Maiana AIS has stopped - Sailoog - 2024-01-03 Do you still have the breakout board? using this board by USB you could confirm where is the problem: https://openplotter.readthedocs.io/en/3.x.x/maiana/connecting.html#breakout-board RE: Maiana AIS has stopped - Lazzz - 2024-01-03 (2024-01-03, 02:16 PM)Sailoog Wrote: Do you still have the breakout board? using this board by USB you could confirm where is the problem: https://openplotter.readthedocs.io/en/3.x.x/maiana/connecting.html#breakout-board I've sent the board & adapter back to Peter so he can check & repair. RE: Maiana AIS has stopped - dreuge - 2024-01-13 Hi, I am trying to install MAIANA AIS in openplotter but I keep getting errors and no AIS received data. I am running on a RaspPi4 with the latest OpenPlotter install w/ Signal-K 2.5.0 & MAIANA AIS 3.1.6-stable. Following instructions, I've configured the serial device using "openplotter-serial" and made the signal-k connection (38,400). All looks fine until I get to openplotter-maiana. When I try to "Refresh" I get an "Unexpected error validating connection: Expected object or value. Try 'Reconnect'." After "Approving" the connection (NEVER w/ read/write) and "Refreshing", I get messages "Cannot connect with device, try again" but now I see "maiana" in the pull down listbox. And repeated "Refresh" and "reconnects" just repeats the "Unexpected error ..." messages. I did prior configure the MAIANA AIS station via the breakout board using a serial terminal. I was able to see the MAIANA NMEA data in the terminal and another vessel has confirmed that I am transmitting correct AIS data. I am not receiving any AIS data. Looking at the Signal-K data browser I do get data for maiana.GP & maiana.GN GPS data, but this GPS data does not get routed to an OpenCPN Signal-K connection nor do I see any AIS data. I tried removing and reinstalling maiana in openplotter with no joy. I kindly ask for any help or insights. Thanks. I get this from the OpenPlotter "Check System":: Checking MAIANA transponder... | MAIANA device: /dev/ttyOP_maiana | device settings OK ↳check device settings check device settings Unexpected error validating connection: Expected object or value. running RE: Maiana AIS has stopped - Sailoog - 2024-01-14 Please go to openplotter-settings and enable "Debugging mode" then open a terminal and type: openplotter-maiana copy here any error in the terminal RE: Maiana AIS has stopped - dreuge - 2024-01-14 (2024-01-14, 11:43 AM)Sailoog Wrote: Please go to openplotter-settings and enable "Debugging mode" then open a terminal and type: I don't seem to be getting any extra debug message other than a few "Gtk-CRITICAL". I ran openplotter-settings and under the "system log" tab I selected "Debugging mode" and received a green text message "Debugging mode enabled. Additional info about errors in OpenPlotter apps will be saved in the sy..." Running openplotter-maiana behaves as before. mypi@openplotter:~ $ openplotter-maiana (openplotter-maiana:63377): Gtk-CRITICAL **: 12:41:32.738: gtk_box_gadget_distribute: assertion 'size >= 0' failed in GtkScrollbar (openplotter-maiana:63377): Gtk-CRITICAL **: 12:41:32.743: gtk_box_gadget_distribute: assertion 'size >= 0' failed in GtkScrollbar I did a system check as noticed that: Checking debugging mode... ↳enabled RE: Maiana AIS has stopped - dreuge - 2024-01-14 Update: While "openplotter-maiana" still fails with "Unexpected error validating connection:" or "Cannot connect with device, try again", I now see some Maiana data in signal-k other than GPS, but still no AIS received data. -------------------DATA BROWSER-------------------------------------------- MAIANA.MCUtype "STM32L432" 01/14 16:03:54 OpenPlotter.maiana MAIANA.bootloader "1" 01/14 16:03:54 OpenPlotter.maiana MAIANA.breakoutGeneration "1" 01/14 16:03:54 OpenPlotter.maiana MAIANA.channelA.noiseFloor 43 01/14 16:03:54 OpenPlotter.maiana MAIANA.channelA.transmittedMessageType "24B" 01/14 16:02:30 OpenPlotter.maiana MAIANA.channelB.noiseFloor 28 01/14 16:03:54 OpenPlotter.maiana MAIANA.channelB.transmittedMessageType "18" 01/14 15:53:41 OpenPlotter.maiana MAIANA.station.LOA 12 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.MMSI "338163026" 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.beam 4 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.bowOffset 10 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.callSign "" 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.portOffset 2 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.vesselName "JOHANNA ROSE" 01/14 15:54:50 OpenPlotter.maiana MAIANA.station.vesselType 36 01/14 15:54:50 OpenPlotter.maiana MAIANA.transmission.hardwarePresent 1 01/14 15:54:50 OpenPlotter.maiana MAIANA.transmission.hardwareSwitch 1 01/14 15:54:50 OpenPlotter.maiana MAIANA.transmission.softwareSwitch 1 01/14 15:54:50 OpenPlotter.maiana MAIANA.transmission.stationData 1 01/14 15:54:50 OpenPlotter.maiana MAIANA.transmission.status 1 01/14 15:54:50 OpenPlotter.maiana --------------------------------------------------------------- RE: Maiana AIS has stopped - Sailoog - 2024-01-15 Just to be clear: - You can ignore these Gtk-CRITICAL errors. - when you get the message "Cannot connect with device, try again", you have to click only "Refresh", do not click "Reconnect". - If the green LED "GPS" is fixed and the serial connection in signal k is correct you should get GPS data in OpenCPN. Make sure there is a connection to the signal k server enabled in opencpn. - The green LED RX should blink when AIS data is received. RE: Maiana AIS has stopped - dreuge - 2024-01-15 (2024-01-15, 12:51 PM)Sailoog Wrote: Just to be clear: Yes, I always first try clicking "Refresh" At first the top pull down menu has "MAIANA Signal K connection" by default with no other options. Clicking Refresh results in the "Unexpected error .." Clicking on "Reconnect", "Approving" w/ the usual "NEVER" and "read/write", and then another "Refresh" results in some too quick to read green text (something like "request was successful..") followed by a red "Cannot connect with the device, try again". But now my MAIANA "maiana" device is listed in the top pulldown box. Another "Refresh" results in the "Unexpected error .." I just discovered something new. I connected to localhost tcp port 10110 38,400 Baud via CoolTerm and I see GPS and AIS NMEA0183 data, for example: "AIVDM,1,1,,B,B52ijK000VLr@>TFa:>KSwbQjCAJ,0*07". I can connect within openCPN to this tcp port and I now receive AIS & GPS via TCP. This did not work when I tried to connect within openCPN via network to the signal k port 3000. Thanks for any insight and help RE: Maiana AIS has stopped - dreuge - 2024-01-30 Hi, Here is an update. I decided to test out the OpenPlotter 4 beta on a RaspPi 5. I am still clueless as to the issues I had with OP3 on my RaspPi 4, but Maiana installed and configured perfectly with OpenPlotter 4 beta on a RaspPi 5. I'm guessing my problem was user error somewhere along the way of setting up my first OP system. Thanks. |