2020-06-12, 12:52 PM
Hi Thomas, with the latest MCS version 2.1.9 everything seems OK. I just have to try it out on the boat. Good wind!
Server Hardware for openplotter?
|
2020-06-12, 12:52 PM
Hi Thomas, with the latest MCS version 2.1.9 everything seems OK. I just have to try it out on the boat. Good wind!
2020-06-14, 12:26 PM
(2020-06-04, 01:35 PM)glowntiger Wrote:(2020-06-03, 02:01 PM)flybob Wrote:Hi flybob,(2020-06-02, 08:46 AM)glowntiger Wrote: For information: Hi ! Really cool that You have released the "how to" and the Python code. Awesome job ! I have done some "fine-tuning" regarding the installation instructions and published it in this post http://pysselilivet.blogspot.com/2020/06...r-diy.html Thanks !
2020-06-14, 08:03 PM
Hi MatsA,
I have read it and have taken a look at the code… Realy good work.. But I have wondered that this nobody have done before. With Pigpio it is very simple??
2020-06-15, 08:50 AM
(2020-06-14, 08:03 PM)glowntiger Wrote: Hi MatsA, Hi Thomas ! Thanks, but You did the job !! It's always simple when You have done it Also did a post on Slack and got a reaction from @tkurki https://app.slack.com/client/T02ENM6QA/C...532.145300 but as said, I don't have the skills......
2020-06-16, 06:50 PM
(2020-06-10, 07:53 AM)glowntiger Wrote: I integrate the pigpio in the next app version. Do not add dependencies to the debian package in control file because dpkg does not install them. Use the post install script,there you can install dependencies and enable services: Code: print(_('Installing dependencies...'))
2020-06-16, 09:53 PM
Tried hooking it up to the St1 bus today and now I got even more data to display. Even got the rudder angle but OpenCPN dashboard really can't handle all the info... Need to display in a better fashion.
Works like a charm, great job Thomas!!
Jeanneau Sun Odyssey 42.2 - All Openplottered and hooked up on online.
2020-06-30, 01:02 PM
New issues arise of course.
Somehow the Course computer seems to know that there's something fishy going on when I've got MCS connected on the ST1 bus. If it's not connected, all instruments wake up and work as expected. As soon as I connect one yellow wire (No Red/Black) from the course computers available ST1 output, the instruments display "Seatalk-Fail" I get all the data in MCS, but the instruments refuse to display theirs instead... Any ideas on why ST fails when I connect the MCS? Note that I only use the yellow wire.
Jeanneau Sun Odyssey 42.2 - All Openplottered and hooked up on online.
2020-06-30, 01:10 PM
Do you have the same gnd potential? The input is only a Optocoppler with an 4,7Kohm resistor. Normaly this should not be a issue for the st1...
HAve you try to connect also the gnd to the board? What kind of ST1 devices are connected? I have try ti with ST60+ (Wind, Depth, Log, Multi) and ST4000+ pilot without any problems....
2020-06-30, 01:25 PM
(2020-06-30, 01:10 PM)glowntiger Wrote: Do you have the same gnd potential? The input is only a Optocoppler with an 4,7Kohm resistor. Normaly this should not be a issue for the st1... I have the exact same problem: Quote:Somehow the Course computer seems to know that there's something fishy going on when I've got MCS connected on the ST1 bus. I tried with only the yellow connected and with yellow and gnd connected. Same issue. Have soldered up a buffer circuit, but have not had a opportunity to test. Will revert next week.
2020-06-30, 01:37 PM
Which devices do you use?
|
« Next Oldest | Next Newest »
|