2021-05-20, 03:42 PM
Hello,
I am new with OpenPlotter, I just installed the OS and want to receive AIS data with a Realtek RTL2832U USB device. It SDR capable, but I don't know to do it.
This is whata I have in dmesg:
How culd I configure it in OpenCPN? Need I install any plugin or software?
I will really appreciate your help.
Kind regards.
I am new with OpenPlotter, I just installed the OS and want to receive AIS data with a Realtek RTL2832U USB device. It SDR capable, but I don't know to do it.
This is whata I have in dmesg:
Code:
[ 9.189096] usb 1-1.4: dvb_usb_v2: found a 'Realtek RTL2832U reference design' in warm state
[ 9.257806] usb 1-1.4: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[ 9.258039] dvbdev: DVB: registering new adapter (Realtek RTL2832U reference design)
[ 9.258130] usb 1-1.4: media controller created
[ 9.262483] dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
[ 9.346598] i2c i2c-11: Added multiplexed i2c bus 12
[ 9.346625] rtl2832 11-0010: Realtek RTL2832 successfully attached
[ 9.346762] usb 1-1.4: DVB: registering adapter 0 frontend 0 (Realtek RTL2832 (DVB-T))...
[ 9.346800] dvbdev: dvb_create_media_entity: media entity 'Realtek RTL2832 (DVB-T)' registered.
[ 9.454689] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
[ 9.484620] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[ 9.484957] usbcore: registered new interface driver brcmfmac
[ 9.524147] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.raspberrypi,3-model-b.txt failed with error -2
[ 9.528021] r820t 12-001a: creating new instance
[ 9.535264] r820t 12-001a: Rafael Micro r820t successfully identified
[ 9.602153] rtl2832_sdr rtl2832_sdr.0.auto: Registered as swradio0
[ 9.602189] rtl2832_sdr rtl2832_sdr.0.auto: Realtek RTL2832 SDR attached
[ 9.602206] rtl2832_sdr rtl2832_sdr.0.auto: SDR API is still slightly experimental and functionality changes may follow
[ 9.624494] Registered IR keymap rc-empty
[ 9.624704] rc rc0: Realtek RTL2832U reference design as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/rc/rc0
[ 9.624984] rc rc0: lirc_dev: driver dvb_usb_rtl28xxu registered at minor = 0, raw IR receiver, no transmitter
[ 9.625261] input: Realtek RTL2832U reference design as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/rc/rc0/input0
[ 9.630738] usb 1-1.4: dvb_usb_v2: schedule remote query interval to 200 msecs
[ 9.639226] usb 1-1.4: dvb_usb_v2: 'Realtek RTL2832U reference design' successfully initialized and connected
[ 9.639606] usbcore: registered new interface driver dvb_usb_rtl28xxuHow culd I configure it in OpenCPN? Need I install any plugin or software?
I will really appreciate your help.
Kind regards.