2017-02-14, 11:10 AM
(This post was last modified: 2017-02-14, 11:13 AM by Alpenskipper.)
Here is the actual open plotter.config (personal data XXX)
Is there a way, I could test googlemail via a CLI command?
[GENERAL]
version = 0.8.0
lang = de
[AIS-SDR]
enable = 0
gain =
ppm =
channel = a
band =
gsm_channel =
[STARTUP]
delay = 0
opencpn = 0
opencpn_no_opengl = 0
opencpn_fullscreen = 1
kplex = 1
x11vnc = 1
vnc_pass = 0
gps_time = 1
nmea_rate_sen = 1
nmea_rate_cal = 1
cal_accuracy = 1
nmea_mag_var = 0
nmea_hdg = 0
nmea_hdt = 0
nmea_press = 1
nmea_temp_p = 1
nmea_hum = 1
nmea_temp_h = 0
nmea_rot = 0
nmea_heel = 0
nmea_pitch = 0
press_temp_log = 1
tw_stw = 0
tw_sog = 0
maximize =
play = 1
sound = /home/pi/.config/openplotter/sounds/Store_Door_Chime.mp3
[SIGNALK]
enable = 1
can_usb = 0
[WIFI]
enable = 1
device = wlan0
share = 0
ssid = Bordnetz
password = XXX
hw_mode = g
channel = 6
wpa = 2
[INPUTS]
switches = [['1', 'AC', 'AC', 12, 'up', 'SW0'], ['1', 'motion', 'motion', 17, 'down', 'SW1']]
[OUTPUTS]
outputs =
[TWITTER]
enable = 0
apikey =
apisecret =
accesstoken =
accesstokensecret =
[GMAIL]
enable = 1
gmail = XXX@gmail.com
password = XXX
recipient = XXX@me.com
[ACTIONS]
triggers = [[0, -1, -1, -1, [['ACT14', '#test', 3.0, 3], ['ACT14', '#ARH [ARH]', 3.0, 3], ['ACT14', '#AP [AP]', 3.0, 3], ['ACT2', '/home/pi/camera.sh', 3.0, 3], ['ACT14', '#IT [AT]', 3.0, 3]]], [0, 'SW0', 7, '1', [['ACT14', '#ACoff', 0.0, 0]]], [0, 'SW0', 8, '0', [['ACT14', '#ACon', 0.0, 0]]], [0, 'SW1', 7, '1', [['ACT14', '#motion', 0.0, 0], ['ACT2', '/home/pi/camera2.sh', 0.0, 0]]]]
[1W]
ds18b20 =
[UDEV]
usbinst = [['ttyOP_gsm', '12d1', '1001', '', '1-1.3.2.4:1.0', 'dev', 'ttyUSB']]
[SMS]
enable = 0
serial = /dev/ttyOP_gsm
bluetooth =
connection = at
enable_sending = 0
phone = 0151253XXX
[MQTT]
broker =
port =
username =
password =
topics =
Is there a way, I could test googlemail via a CLI command?
[GENERAL]
version = 0.8.0
lang = de
[AIS-SDR]
enable = 0
gain =
ppm =
channel = a
band =
gsm_channel =
[STARTUP]
delay = 0
opencpn = 0
opencpn_no_opengl = 0
opencpn_fullscreen = 1
kplex = 1
x11vnc = 1
vnc_pass = 0
gps_time = 1
nmea_rate_sen = 1
nmea_rate_cal = 1
cal_accuracy = 1
nmea_mag_var = 0
nmea_hdg = 0
nmea_hdt = 0
nmea_press = 1
nmea_temp_p = 1
nmea_hum = 1
nmea_temp_h = 0
nmea_rot = 0
nmea_heel = 0
nmea_pitch = 0
press_temp_log = 1
tw_stw = 0
tw_sog = 0
maximize =
play = 1
sound = /home/pi/.config/openplotter/sounds/Store_Door_Chime.mp3
[SIGNALK]
enable = 1
can_usb = 0
[WIFI]
enable = 1
device = wlan0
share = 0
ssid = Bordnetz
password = XXX
hw_mode = g
channel = 6
wpa = 2
[INPUTS]
switches = [['1', 'AC', 'AC', 12, 'up', 'SW0'], ['1', 'motion', 'motion', 17, 'down', 'SW1']]
[OUTPUTS]
outputs =
[TWITTER]
enable = 0
apikey =
apisecret =
accesstoken =
accesstokensecret =
[GMAIL]
enable = 1
gmail = XXX@gmail.com
password = XXX
recipient = XXX@me.com
[ACTIONS]
triggers = [[0, -1, -1, -1, [['ACT14', '#test', 3.0, 3], ['ACT14', '#ARH [ARH]', 3.0, 3], ['ACT14', '#AP [AP]', 3.0, 3], ['ACT2', '/home/pi/camera.sh', 3.0, 3], ['ACT14', '#IT [AT]', 3.0, 3]]], [0, 'SW0', 7, '1', [['ACT14', '#ACoff', 0.0, 0]]], [0, 'SW0', 8, '0', [['ACT14', '#ACon', 0.0, 0]]], [0, 'SW1', 7, '1', [['ACT14', '#motion', 0.0, 0], ['ACT2', '/home/pi/camera2.sh', 0.0, 0]]]]
[1W]
ds18b20 =
[UDEV]
usbinst = [['ttyOP_gsm', '12d1', '1001', '', '1-1.3.2.4:1.0', 'dev', 'ttyUSB']]
[SMS]
enable = 0
serial = /dev/ttyOP_gsm
bluetooth =
connection = at
enable_sending = 0
phone = 0151253XXX
[MQTT]
broker =
port =
username =
password =
topics =