This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Navman wind 3100s no nmea to OP
#1
Hi, I just installed an used wind instrument on boat, I would like to send the nmea0183 sentence (IIMWV and IIVPW) to Openplotter is it possible?

Nmea out from wind instrument to A+ and ground to B+ of the serial/USB adaptor

In the nmea tab I selected the USB1, 4800 baud, apply change, restart but no sentences on inspector. I also tried to applying filters to IN sentences but no joy

Op 8.0

Ideas?

CheersĀ 
Reply
#2
nobody knows??
Reply
#3
Op 0.8.0 ?
little to no support for that ver.
newer
http://www.sailoog.com/blog/download-ope...0100-noobs
then update takes hours be patient
0.17.1 is the stable ver. now
https://github.com/sailoog/openplotter/b...ANGELOG.md
Reply
#4
thanks a lot I will try
Reply
#5
I updated to last stable.. but no joy....

[Image: 151b9d3a11cefb591eb4e7d73d36e4f3.jpg]

Is it correct the connection I made?
How can I test nmea output of wind instrument?


Inviato dal mio iPad utilizzando Tapatalk
Reply
#6
http://forum.openmarine.net/showthread.p...47#pid4847
usb serial adapter ?
Reply
#7
Tnks a lot, I Will try soon with this:
https://www.amazon.fr/Generic-RS232-Seri...8YMWSGRGK5

And this:

https://www.amazon.fr/femelle-adaptateur...0E5BDHSASP

I will post here the result.........


Inviato dal mio iPad utilizzando Tapatalk
Reply
#8
I tested the rs232/USB adapter with the wind and it worked connecting the white cable to pin 2 of the serial and gnd to pin 5.
I tested also with the autopilot raymarine st 1000+ but no joy... during and after this second test the serial adapter is not more visible in the port menu/add window/nmea tab....

NEVER A JOY!!!!!!


Op 11.11
Rpi3
Gps bt amtec
Imu MPU 9250
Pressure BMP180
Temperature HTU21D
Humidity HTU21D
dAISy
Reply
#9
(2018-04-08, 03:43 PM)callmecalanca Wrote: I tested the rs232/USB adapter with the wind and it worked connecting the white cable to pin 2 of the serial and gnd to pin 5.
I tested also with the autopilot raymarine st 1000+ but no joy... during and after this second test the serial adapter is not more visible in the port menu/add window/nmea tab....

NEVER A JOY!!!!!!


Op 11.11
Rpi3
Gps bt amtec
Imu MPU 9250
Pressure BMP180
Temperature HTU21D
Humidity HTU21D
dAISy






Op 0.17
Rpi3
Gps USB
Imu MPU 9250
Pressure BMP180
Temperature HTU21D
Humidity HTU21D
Ais tv dongle
Adafruit thermal printer
Navman Wind 3100
Navman echo
Raymarmarine st1000+
Ina3221
Reply
#10
Remember the TX from the Wind goes to the RX of the autopilot, not TX to TX.

Drop into terminal.


try these commands:


lsusb


make sure your usb adapter or adapters are showing.


dmesg | grep tty


should be able to find the ports linux has given your serial ports.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)