This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 2 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Server Hardware for openplotter?
#71
In principle yes,  but the adapter is not ready  until now. If all runs well, i make the adapter. 
The pins of the moitessier and the MCS are compatible.

(2019-10-06, 02:30 PM)jim321 Wrote: the 40 pin header could be changed to a stackable one with the socket on the back for the pi and pins on front to plug in the  Moitessier hat. ?
40 pin cable with two connectors.?

Yes, but until now i did not find one. ?
Reply
#72
The Moitessier hat also uses some pins exclusively. any possible conflict?
Reply
#73
(2019-10-06, 03:17 PM)Sailabout Wrote: The Moitessier hat also uses some pins exclusively. any possible conflict?

No, i have only used pins which are free... i2c was shared. There should be no address conflict if I had study the manual right.... spi I used ce2.
Reply
#74
(2019-10-06, 03:35 PM)glowntiger Wrote:
(2019-10-06, 03:17 PM)Sailabout Wrote: The Moitessier hat also uses some pins exclusively. any possible conflict?

No, i have only used pins which are free... i2c was shared. There should be no address conflict if I had study the manual right.... spi I used ce2.

Well I saw the progress, as I said I wait for you to tell me when everything is ready. The new card is perfect. Good job. OP2 is moving forward and I hope the Beta version will arrive soon. Great job Sailoog!   Smile Smile Smile
Reply
#75
Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins)
   

Until I get a Moitessier hat I will check if all works fine together... Tongue
Reply
#76
(2019-10-07, 07:58 AM)glowntiger Wrote: Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins)


Until I get a Moitessier hat I will check if all works fine together... Tongue

Can help?  :https://www.amazon.com/40-pin-connector/...+connector
Reply
#77
(2019-10-07, 10:10 AM)Max1947 Wrote:
(2019-10-07, 07:58 AM)glowntiger Wrote: Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins)


Until I get a Moitessier hat I will check if all works fine together... Tongue

Can help?  :https://www.amazon.com/40-pin-connector/...+connector

Yes,
after some search I have found one.
This should work:
https://www.amazon.com/Connectors-Raspbe...09&sr=8-51
Then  I only need longer distance adapter to moitessier hat.... Wink Cool Big Grin
I have ordered some to check. Now I only need a moitessier hat Confused 
Has anybody a moitessier hat and want to check if all works fine now?
Reply
#78
https://www.aliexpress.com/item/32868096...b201603_52

if the female header is on top to plug the hat, and the pi on the other side of board to pins
stacked together no cable needed
Reply
#79
(2019-10-07, 11:57 AM)glowntiger Wrote:
(2019-10-07, 10:10 AM)Max1947 Wrote:
(2019-10-07, 07:58 AM)glowntiger Wrote: Qui puoi vedere i Pin usati della scheda MCS: (in Black the Moitessier Pins)


Finché non avrò un cappello Moitessier controllerò se tutto funziona bene insieme ... Tongue

Può aiutare? : https://www.amazon.com/40-pin-connector/...+connector

Sì,
dopo alcune ricerche ne ho trovato uno.
Dovrebbe funzionare:
https://www.amazon.com/Connectors-Raspbe...09&sr=8-51
Quindi Ho solo bisogno di un adattatore di distanza maggiore per il cappello moitessier .... Wink Cool Big Grin
Ne ho ordinato alcuni per controllare. Ora ho solo bisogno di un cappello moitessier Confused 
Qualcuno ha un cappello moitessier e voglio verificare se tutto funziona bene ora?

Ciao, ho il Moitessier ma non so come fare i controlli. Ho tutto a casa, non sulla barca. Se posso essermi utile e spiegarmi, puoi inviarmi la scheda e i vari accessori per la connessione. Potrei collegare un "A5130 autonnico con uscita NMEA-2000" (vedi: https://www.autonnic.com/marine-industrial-sensors) un sensore di temperatura DS18B20 e anche un sensore del vento NMEA 0183 MWV "NASA Marine Clipper" " Dammi il costo della carta anche in PM, e ti pagherò, ma come ho detto, non essendo un elettronico, devi dirmi cosa fare per le connessioni, ecc. Aspetto notizie e ti saluto .     Idea Big Grin

Ancora una volta, se questo adattatore può essere utile per la tua carta: 
Adathttps://www.sg-electronic-systems.com/ecommerce/can-bus-shield/21-quad-can-adapter-quad-can-bus-is-an-open-hardware-to-connect-a-couple-of-canber-boards-to-raspberry-pi-in-this-way-it-is-possi.htmltatore
Reply
#80
after a closer look the 12v area could interfere with the compass on the Moitessier hat.so a cable would move it away from that.
i guess it will need to be tested ..hope it works.
Reply


Forum Jump:


Users browsing this thread: 21 Guest(s)