This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Server Hardware for openplotter?
(12-02-2019, 08:37 AM)glowntiger Wrote: Hi,
if someone who has a board would like to test, i have add an autoshutdown to the MCS-modul.
Now you can use it directly via the App. If you enable the Checkbox the pi should shutdown if you bring the 12V enable terminal to gnd. After 40s the MCS-PCB power off the Pi and you be able to restart the Pi....

Hi, explain ... do I have to uninstall your app and clone the new one? Fixed Linux driver?  Huh Big Grin
  Reply
Hi Max,
go on your Pi and type:


Code:
sudo rm -r openplotter-MCS

to delete the folder.
then load the new git data:

Code:
git clone https://github.com/Thomas-GeDaD/openplotter-MCS
then go to the folder:

Code:
cd openplotter-MCS

and install:


Code:
sudo python3 setup.py install

now you can start the openplotter APP:


PHP Code:
openplotter-MCS 


there is a new service in the background (openplotter-MCS-asd) if you enable the autoshutdown in the app, the Pi shuts down after power off the +12V enable Terminal.

You must one time start the app and push save for starting the Service. Until now the app is not handle by openplotter... I hope sailoog do this the next time.

The driver issue is a timing problem of the adresses. I have change the adress of the third sc16is752 on the hardware side. I have order 20 new MCS an they should arrived the next days. At the moment you can only use 4 of the 6 NMEA0183 ports.
All who have get a prototype board gets a new MCS if availible....

https://github.com/raspberrypi/linux/issues/3340

here you find info´s to the issue
  Reply
(12-03-2019, 04:07 AM)glowntiger Wrote: Hi Max,
go on your Pi and type:


Code:
sudo rm -r openplotter-MCS

to delete the folder.
then load the new git data:

Code:
git clone https://github.com/Thomas-GeDaD/openplotter-MCS
then go to the folder:

Code:
cd openplotter-MCS

and install:


Code:
sudo python3 setup.py install

now you can start the openplotter APP:


PHP Code:
openplotter-MCS 


there is a new service in the background (openplotter-MCS-asd) if you enable the autoshutdown in the app, the Pi shuts down after power off the +12V enable Terminal.

You must one time start the app and push save for starting the Service. Until now the app is not handle by openplotter... I hope sailoog do this the next time.

The driver issue is a timing problem of the adresses. I have change the adress of the third sc16is752 on the hardware side. I have order 20 new MCS an they should arrived the next days. At the moment you can only use 4 of the 6 NMEA0183 ports.
All who have get a prototype board gets a new MCS if availible....

https://github.com/raspberrypi/linux/issues/3340

here you find info´s to the issue

Hi, I followed the instructions but I must have been wrong, see photo. I book for the new card and I hope that in the meantime Sailoog and Rocco make progress. I hope everything is ready for spring and try it all on my boat. Ok, winter is still long, there's time ... good job everyone!

[img][Image: vwqWDI.jpg][/img]

[img][Image: kiCBQk.jpg][/img]
  Reply
Hi Max,
Sorry i have missed two "". Please try again. The same procedure….

Why you have add a ventilation? It´s not needed… You did not get temperature problems…
But looks good…
  Reply
(12-03-2019, 12:37 PM)glowntiger Wrote: Hi Max,
Sorry i have missed two "". Please try again. The same procedure….

Why you have add a ventilation? It´s not needed… You did not get temperature problems…
But looks good…

Ok, I repeated everything a couple of times and now it's all right. More than the fan (which is actually not needed) I wanted to see the various LEDs to make sure that it was working properly. I had this available and can temporarily go! I also added the switch ...

Smile Big Grin
  Reply
Did the pi shut Down?
  Reply
(12-03-2019, 03:12 PM)glowntiger Wrote: Did the pi shut Down?

Ciao, guarda:

[img][Image: lOE1S6.jpg][/img]
  Reply
Hi MAx,
Sorry I have forgotten one step.
The Installation.... Sad Angel 
Do:

Code:
sudo MCSPreUninstall
Code:
sudo MCSPostInstall



Without the Service isn´t availible
  Reply
(Today, 04:12 AM)glowntiger Wrote: Hi MAx,
Sorry I have forgotten one step.
The Installation.... Sad Angel 
Do:

Code:
sudo MCSPreUninstall
Code:
sudo MCSPostInstall

.... now it's all right, I always apologize for my ignorance, but a nice step-by-step instruction in the configuration is indispensable for those like me, tanks and the next ... bye!  Big Grin Big Grin Big Grin

Without the Service isn´t availible
  Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)