This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Connect autohelm to op
#1
Last year i successfully installed op in my boat. It gives me a optimum support during my navigation in the north adriac see.
Now i would like to implement my configuration connecting my autohelm to op, basically for the batimetric and wind misure.
I have the instrument panel and the plug as show below... Sameone can explain in a simple way how can i connect them to op?
Thank you for all your help and support

[Image: 584fc99645a085da9b0423b5b30ee78b.jpg][Image: 010471252fdc79392477f01214ae344e.jpg][Image: fb61579ad1683924c1bebe9f844544c6.jpg]

Inviato dal mio ANE-LX2 utilizzando Tapatalk
Reply
#2
Unfortunately ST50 TRIDATA and ST50 Wind instrument has no NMEA 0183 interface for connecting third party equipment (only ST50+ TRIDATA REPEATER and Autohelm MFD has it).
Tridata and Wind displays only has Seatalk interface (3pin connector on your picture)

You need some kind of Seatalk->NMEA 0183 converter, for example Raymarine "PC/Seatalk/NMEA Interface BOX" (some call it RS232 BOX) which is hard to find and not so cheap (for my taste)

PS: I see second seatalk cable on your picture (from wind instrument) which is leading to some another place. It is just power or i guess you have at least one another device in your seatalk network. What is it? Is it Repeater?
Reply
#3
Thank you.
This one can make the work? https://www.painestore.it/convertitore_s...vMEALw_wcB

Something cheaper exists?



I though it was 1 camble for wind and 1 for depth... But i never check. Next time i will

Inviato dal mio ANE-LX2 utilizzando Tapatalk
Reply
#4
That device is for Seatalk NG. The instruments you showed use first generation Seatalk. You need a two way Seatalk bridge.

Sent from my CLT-L04 using Tapatalk
Reply
#5
(2020-02-23, 12:11 PM)luchin0 Wrote: Thank you.
This one can make the work? https://www.painestore.it/convertitore_s...vMEALw_wcB

Something cheaper exists?



I though it was 1 camble for wind and 1 for depth... But i never check. Next time i will

Inviato dal mio ANE-LX2 utilizzando Tapatalk

Hi, you should use this. It's also cheap ... good wind!  Shy
Http: //yakbitz.com/ST1toNMEA.aspx
Reply
#6
Thank you for your suggestion.

How i connect it to my rpi with moittesier hat?

Difference with this one?
https://www.ebay.it/itm/SEAYAK-Seatalk1-...3224200076

Inviato dal mio ANE-LX2 utilizzando Tapatalk
Reply
#7
(2020-02-23, 04:49 PM)luchin0 Wrote: Thank you for your suggestion.

How i connect it to my rpi with moittesier hat?

Difference with this one?
https://www.ebay.it/itm/SEAYAK-Seatalk1-...3224200076

Inviato dal mio ANE-LX2 utilizzando Tapatalk

Hi, it's the same I indicated. It comes from Australia (it will take some time, but the seller is serious). You must connect the output of your instruments (identifying the three corresponding colors: red + black mass or gnd- yellow Seatalk data) to the "Seyak" and connect it with the cable in dodation to a USB port of the rpi. Good job  Smile
Reply
#8
Is that device bi-directional?
Reply
#9
(2020-02-23, 10:39 PM)Techstyle Wrote: Is that device bi-directional?

No.! Big Grin
Reply
#10
(2020-02-24, 10:26 AM)Max1947 Wrote:
(2020-02-23, 10:39 PM)Techstyle Wrote: Is that device bi-directional?

No.! Big Grin
Full dupplex with conversion all navi standard ( nmea183, NMEA2000 and SeaTalk) are this
https://ocenav.com/en/home/
That's the one I have on my boat. I have the same ST50 system

Gesendet von meinem CLT-L29 mit Tapatalk
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)