2016-12-08, 10:32 AM
[quote pid='908' dateline='1481131085']
.1. LAN and Wifi connections are working limited -BUT- the icon for the LAN connections is greyed out and when trying to configure LAN connections it says "No Connections to Configure". I can still browse the web etc, LAN traffic is working
2. When in OpenPlotter, no networking connections (TCP/IP) show up to add to KFLEX or to redirect inside SignalK.
3. It may be that the Pi System does not recognize the LAN under this 0.9.0alpha NOOBS but you cannot configure and get the NEMA 0183 stream onto the TCP/IP and out the door for use on the LAN.
4. I2C sensors, I noticed the pressure and temp not showing up inside Openplotter now.
5. NEMA 2K tab, if you check/select which PGNs you want to transmit, the PGNs do not show up in the output box on that tab.
6. VNC is greyed out within Raspbi Config but works when VNC from remote computer
7. IC2 temp probe is reconised but cannot get data to transmit. (Maybe I'm still learning the new version)
[/quote]
1. and 3. Have you read
https://sailoog.gitbooks.io/openplotter-...fi-ap.html
What have you configured in WiFi AP?
2. The stream from kplex to signalk can't be deleted (page NMEA 0183 third line signalk)
3. The stream from kplex to opencpn can't be deleted (page NMEA 0183 second line opencpn) Becareful this was 10110 and has changed to 10109! SignalK already used the port 10110. All devices which connected to openplotter/kplex in 0.8 have to change this!
4. Where did you seek for the temperature? Openplotter doesn't produce any NMEA 0183 automatically (XDR formats aren't normed there is much confusion).
The sensors are sending to SignalK and should be in the SignalK diagnostic page. Have a look at
https://sailoog.gitbooks.io/openplotter-...gnalk.html
If you want to have a NMEA 0183 sentence for some SignalK data you can use the NMEA 0183 generator.
5. It seems that you only have told the hardware not to block PGNs. This is only the first step.
You have to select NMEA 2000 generator (https://sailoog.gitbooks.io/openplotter-...ea-2k.html)
6. You are right Openplotter uses a different VNC prog. You can select it on Startup page.
7. Do you mean i2c temperature? Have you select a SignalK name on I2C sensor page?
The documentation has been updated at some places. Most users don't know that.
.1. LAN and Wifi connections are working limited -BUT- the icon for the LAN connections is greyed out and when trying to configure LAN connections it says "No Connections to Configure". I can still browse the web etc, LAN traffic is working
2. When in OpenPlotter, no networking connections (TCP/IP) show up to add to KFLEX or to redirect inside SignalK.
3. It may be that the Pi System does not recognize the LAN under this 0.9.0alpha NOOBS but you cannot configure and get the NEMA 0183 stream onto the TCP/IP and out the door for use on the LAN.
4. I2C sensors, I noticed the pressure and temp not showing up inside Openplotter now.
5. NEMA 2K tab, if you check/select which PGNs you want to transmit, the PGNs do not show up in the output box on that tab.
6. VNC is greyed out within Raspbi Config but works when VNC from remote computer
7. IC2 temp probe is reconised but cannot get data to transmit. (Maybe I'm still learning the new version)
[/quote]
1. and 3. Have you read
https://sailoog.gitbooks.io/openplotter-...fi-ap.html
What have you configured in WiFi AP?
2. The stream from kplex to signalk can't be deleted (page NMEA 0183 third line signalk)
3. The stream from kplex to opencpn can't be deleted (page NMEA 0183 second line opencpn) Becareful this was 10110 and has changed to 10109! SignalK already used the port 10110. All devices which connected to openplotter/kplex in 0.8 have to change this!
4. Where did you seek for the temperature? Openplotter doesn't produce any NMEA 0183 automatically (XDR formats aren't normed there is much confusion).
The sensors are sending to SignalK and should be in the SignalK diagnostic page. Have a look at
https://sailoog.gitbooks.io/openplotter-...gnalk.html
If you want to have a NMEA 0183 sentence for some SignalK data you can use the NMEA 0183 generator.
5. It seems that you only have told the hardware not to block PGNs. This is only the first step.
You have to select NMEA 2000 generator (https://sailoog.gitbooks.io/openplotter-...ea-2k.html)
6. You are right Openplotter uses a different VNC prog. You can select it on Startup page.
7. Do you mean i2c temperature? Have you select a SignalK name on I2C sensor page?
The documentation has been updated at some places. Most users don't know that.