Today I went on board:
- I turned off power and back on everything.
- I unplugged the sensor imu
- I repeated the test with a new microSD with a clean install.
- Diagnostic continues to not show the AIS sentences (nothing on system, nothing of opencpn of kplesk).
- If I off "AIS Reception" AIS the from terminal I see the strings:
pi@openplotter:~ $ rtl_fm -f 161975000 -p 0 -s 48k | aisdecoder -h 127.0.0.1 -p 1 -a file -c mono -d -f /dev/stdin
Found 1 device(s):
0: Realtek, RTL2838UHIDIR, SN: 00000001
Using device 0: Generic RTL2832U OEM
Found Rafael Micro R820T tuner
Tuner gain set to automatic.
Tuned to 162227000 Hz.
Oversampling input by: 21x.
Oversampling output by: 1x.
Buffer size: 8.13ms
Exact sample rate is: 1008000.009613 Hz
Sampling at 1008000 S/s.
Output at 48000 Hz.
!AIVDM,1,1,,A,402Fhbiv4d`UE0ruhtI8PaW0052D,0*1C
!AIVDM,1,1,,A,402FhPAv4d`UK0vB:dHrqSW00`@F,0*04
!AIVDM,1,1,,A,ENjO`A32qIrJ@1WV62h1P`8:QQTPNsn7<NhNp10888N003R@,0*25
!AIVDM,1,1,,A,ENjO`A32qIrJ@1WV62h1P`8:QQTPNsn7<NhNp10888N003R@,0*25
!AIVDM,1,1,,A,402FhPAv4d`UR0vB:dHrqSW00U2D,0*58
I understand the problem and solved!
In .kplex.conf configuration file in the system section must be added the voice address=localhost
This is missing in the files installed by openplotter.
Like this is ok:
[udp]
name=system
direction=in
address=localhost
port=10110
- I turned off power and back on everything.
- I unplugged the sensor imu
- I repeated the test with a new microSD with a clean install.
- Diagnostic continues to not show the AIS sentences (nothing on system, nothing of opencpn of kplesk).
- If I off "AIS Reception" AIS the from terminal I see the strings:
pi@openplotter:~ $ rtl_fm -f 161975000 -p 0 -s 48k | aisdecoder -h 127.0.0.1 -p 1 -a file -c mono -d -f /dev/stdin
Found 1 device(s):
0: Realtek, RTL2838UHIDIR, SN: 00000001
Using device 0: Generic RTL2832U OEM
Found Rafael Micro R820T tuner
Tuner gain set to automatic.
Tuned to 162227000 Hz.
Oversampling input by: 21x.
Oversampling output by: 1x.
Buffer size: 8.13ms
Exact sample rate is: 1008000.009613 Hz
Sampling at 1008000 S/s.
Output at 48000 Hz.
!AIVDM,1,1,,A,402Fhbiv4d`UE0ruhtI8PaW0052D,0*1C
!AIVDM,1,1,,A,402FhPAv4d`UK0vB:dHrqSW00`@F,0*04
!AIVDM,1,1,,A,ENjO`A32qIrJ@1WV62h1P`8:QQTPNsn7<NhNp10888N003R@,0*25
!AIVDM,1,1,,A,ENjO`A32qIrJ@1WV62h1P`8:QQTPNsn7<NhNp10888N003R@,0*25
!AIVDM,1,1,,A,402FhPAv4d`UR0vB:dHrqSW00U2D,0*58
I understand the problem and solved!
In .kplex.conf configuration file in the system section must be added the voice address=localhost
This is missing in the files installed by openplotter.
Like this is ok:
[udp]
name=system
direction=in
address=localhost
port=10110