GY-87 signalk doesn't work

[Luckbert]

Hallo zusammen,
Ich habe schon einen Thread in "wie ich das mache?" Geschrieben
Meine Sensoren werden nicht erkannt. In signalk wird nicht angezeigt.
Ich habe ein GY-87 Modul installiert. MPU-9150 und BMP180 sind installiert.
Ich kann die MPU kalibrieren und es im Eingabeschild diagnostisch sehen. In der Diagnose des kplex aber ich kann nichts sehen
Das BMP kann nur die Hälfte in der Signalkiagnose sehen. Ich sehe den Luftdruck, aber keine Temperatur. In der Kplex-Diagnose ist kein Sensor zu sehen.
Im Tap I2C sehe ich nur das BMP. Bei der Temperatur fehlt die Signalknote.
Ich füge noch Bilder hinzu.
Grüße Jürgen

[Luckbert]

Hello everybody,
I think the error lies in the signalk. If I use the simulator nevertheless no data arrive.
Does somebody has any idea? Can I reinstall Signalk? If yes how ?
Greetings Jürgen

Hallo zusammen,
Ich denke der Fehler liegt im Signalk. Wen ich den Simulator benutze kommen trotzdem keine Daten an.
Hat jemand eine Idee? Kann ich Signalk nachinstallieren .? Wenn ja, wie ?
Grüße Jürgen

[Luckbert]

Hello everybody,
I have further tested. I can use the values ​​of the MPU-9150 and the BMP-180 to trigger actions.
So it seems so so "only" the connection to Kplex would be defective.
How can I check the connection or create a new one?
Greetings Jürgen

[Luckbert]

Hello,
Are you all on vacation? 
Or do you make an update? 

I have run the "python update_signalk_settings.py" file.
This caused the following error:

Traceback (most recent call last):  File "update_signalk_settings.py", line 20, in <module>    Back_path = sys.argv [1]IndexError: listIndex out of rangeDoes that help?

Greetings Jürgen

[e-sailing]

Some settings have been changed in 14.
All compass settings have been pushed from i2c Tab to compass tab.
There are default SignalK settings for humidity and pressure but not for temperature. Double click on the temperature line in i2c tab.
Select environment water/inside/outside/... temperature.
If these values are visible in signalk diagnostic-> SignalK is OK.
In the tool section -> calculation has changed (no switch for 0.8 compatibility anymore which generates the old nmea 0183 sentences)
If sailoog merges the pull request #177. There will be a default button to generate opencpn compatible nmea sentences in nmea0183 generator for:
-compass
-roll
-pitch
-air pressure
-water temp
-air temp

update_signalk_settings.py is part of update_settings.sh
It should be used only within update_settings.sh

If you want to reinstall signalk from terminal do:
cd .config
mv signalk-server-node signalk-server-node-bak
git clone https://github.com/SignalK/signalk-server-node.git
cd signalk-server-node
npm install
sudo reboot

[Luckbert]

Some settings have been changed in 14.
All compass settings have been pushed from i2c Tab to compass tab.
There are default SignalK settings for humidity and pressure but not for temperature. Double click on the temperature line in i2c tab.Nothing happens. No reaction from OP

Select environment water/inside/outside/... temperature.
If these values are visible in signalk diagnostic-> SignalK is OK.
In the tool section -> calculation has changed (no switch for 0.8 compatibility anymore which generates the old nmea 0183 sentences)
If sailoog merges the pull request #177. There will be a default button to generate opencpn compatible nmea sentences in nmea0183 generator for:
-compass
-roll
-pitch
-air pressure
-water temp
-air temp

update_signalk_settings.py is part of update_settings.sh
It should be used only within update_settings.sh

If you want to reinstall signalk from terminal do:
cd .config
mv signalk-server-node signalk-server-node-bak 
cd signalk-server-node
npm install
sudo reboot

Greetings Jürgen

[Sailoog]

Could you please update to latest version, delete all your defined I2C devices, define them again and try the new button on NMEA 0183 generator that e-sailing suggested?