In principle yes, but the adapter is not ready until now. If all runs well, i make the adapter.
The pins of the moitessier and the MCS are compatible.
(2019-10-06, 02:30 PM)jim321 Wrote: [ -> ]the 40 pin header could be changed to a stackable one with the socket on the back for the pi and pins on front to plug in the Moitessier hat. ?
40 pin cable with two connectors.?
Yes, but until now i did not find one. ?
The Moitessier hat also uses some pins exclusively. any possible conflict?
(2019-10-06, 03:17 PM)Sailabout Wrote: [ -> ]The Moitessier hat also uses some pins exclusively. any possible conflict?
No, i have only used pins which are free... i2c was shared. There should be no address conflict if I had study the manual right.... spi I used ce2.
Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins)
[
attachment=575]
Until I get a Moitessier hat I will check if all works fine together...
(2019-10-07, 10:10 AM)Max1947 Wrote: [ -> ] (2019-10-07, 07:58 AM)glowntiger Wrote: [ -> ]Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins)
Until I get a Moitessier hat I will check if all works fine together...
Can help? :https://www.amazon.com/40-pin-connector/...+connector
Yes,
after some search I have found one.
This should work:
https://www.amazon.com/Connectors-Raspbe...09&sr=8-51
Then I only need longer distance adapter to moitessier hat....
I have ordered some to check. Now I only need a moitessier hat
Has anybody a moitessier hat and want to check if all works fine now?
(2019-10-07, 11:57 AM)glowntiger Wrote: [ -> ] (2019-10-07, 10:10 AM)Max1947 Wrote: [ -> ] (2019-10-07, 07:58 AM)glowntiger Wrote: [ -> ]Qui puoi vedere i Pin usati della scheda MCS: (in Black the Moitessier Pins)
Finché non avrò un cappello Moitessier controllerò se tutto funziona bene insieme ...
Può aiutare? : https://www.amazon.com/40-pin-connector/...+connector
Sì,
dopo alcune ricerche ne ho trovato uno.
Dovrebbe funzionare:
https://www.amazon.com/Connectors-Raspbe...09&sr=8-51
Quindi Ho solo bisogno di un adattatore di distanza maggiore per il cappello moitessier ....
Ne ho ordinato alcuni per controllare. Ora ho solo bisogno di un cappello moitessier
Qualcuno ha un cappello moitessier e voglio verificare se tutto funziona bene ora?
Ciao, ho il Moitessier ma non so come fare i controlli. Ho tutto a casa, non sulla barca. Se posso essermi utile e spiegarmi, puoi inviarmi la scheda e i vari accessori per la connessione. Potrei collegare un "A5130 autonnico con uscita NMEA-2000" (vedi:
https://www.autonnic.com/marine-industrial-sensors) un sensore di temperatura DS18B20 e anche un sensore del vento NMEA 0183 MWV "NASA Marine Clipper" " Dammi il costo della carta anche in PM, e ti pagherò, ma come ho detto, non essendo un elettronico, devi dirmi cosa fare per le connessioni, ecc. Aspetto notizie e ti saluto .
Ancora una volta, se questo adattatore può essere utile per la tua carta:
Adathttps://www.sg-electronic-systems.com/ecommerce/can-bus-shield/21-quad-can-adapter-quad-can-bus-is-an-open-hardware-to-connect-a-couple-of-canber-boards-to-raspberry-pi-in-this-way-it-is-possi.htmltatore
after a closer look the 12v area could interfere with the compass on the Moitessier hat.so a cable would move it away from that.
i guess it will need to be tested ..hope it works.