Hello
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
hello,
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
Found 1 device(s):
0: Generic RTL2832U OEM
Using device 0: Generic RTL2832U OEM
Detached kernel driver
Found Rafael Micro R820T tuner
Exact sample rate is: 270833.002142 Hz
[R82XX] PLL not locked!
kal: Scanning for GSM-900 base stations.
GSM-900:
-----------------------------------------------------------------------
Take note of the channel with the highest power value and press Enter to close this window.
-----------------------------------------------------------------------
(2020-04-27, 05:58 PM)Romarin Wrote: [ -> ]Hello
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
hello,
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
What is de outcome if you do this in the terminal. Does it show enabled ?
sudo systemctl status openplotter-rtl_ais.service
Try with the setting with autostart to on.
Bram
(2020-04-27, 06:12 PM)What is de outcome if you do this in the terminal. Does it show enabled ? Wrote: [ -> ]sudo systemctl status openplotter-rtl_ais.service
Try with the setting with autostart to on.
Bram
● openplotter-rtl_ais.service - Decode AIS received by rtl-sdr and send as NMEA 0183 to UDP port
Loaded: loaded (/etc/systemd/system/openplotter-rtl_ais.service; disabled; vendor preset: enabled)
Active: active (running) since Mon 2020-04-27 19:02:45 CEST; 3min 16s ago
Main PID: 2932 (rtl_ais)
Tasks: 4 (limit: 4915)
Memory: 1.3M
CGroup: /system.slice/openplotter-rtl_ais.service
└─2932 /usr/bin/rtl_ais -d 0 -p 0 -P 10110
avril 27 19:02:45 openplotter rtl_ais[2932]: Downsample factor: 64
avril 27 19:02:45 openplotter rtl_ais[2932]: Low pass: 25000 Hz
avril 27 19:02:45 openplotter rtl_ais[2932]: Output: 48000 Hz
avril 27 19:02:45 openplotter rtl_ais[2932]: Found Rafael Micro R820T tuner
avril 27 19:02:45 openplotter rtl_ais[2932]: Log NMEA sentences to console OFF
avril 27 19:02:45 openplotter rtl_ais[2932]: AIS data will be sent to 127.0.0.1 port 10110
avril 27 19:02:45 openplotter rtl_ais[2932]: Tuner gain set to automatic.
avril 27 19:02:45 openplotter rtl_ais[2932]: Tuned to 162000000 Hz.
avril 27 19:02:46 openplotter rtl_ais[2932]: Sampling at 1600000 S/s.
avril 27 19:02:46 openplotter rtl_ais[2932]: Allocating 12 zero-copy buffers
~
~
~
~
~
~
~
~
~
~
~
~
~
~
(2020-04-27, 05:58 PM)Romarin Wrote: [ -> ]Hello
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
hello,
I have a device that appears when I turn my SDR dongle, but it doesn't work.
It is a Nooelec NESDR SmArTee V2 SDR, RTL2832U & R820T2 based.
RPi4.
Found 1 device(s):
0: Generic RTL2832U OEM
Using device 0: Generic RTL2832U OEM
Detached kernel driver
Found Rafael Micro R820T tuner
Exact sample rate is: 270833.002142 Hz
[R82XX] PLL not locked!
kal: Scanning for GSM-900 base stations.
GSM-900:
-----------------------------------------------------------------------
Take note of the channel with the highest power value and press Enter to close this window.
-----------------------------------------------------------------------
I seems that you do not have strong GSM channnels.
Delete the AIS assignation to be sure any program is using the device and open a terminal and type:
kal -d 0 -s GSM900 -g 49.6
(2020-04-27, 07:18 PM)Il semble que vous n\ayez pas de canaux GSM puissants. Wrote: [ -> ]Romarin
Delete the AIS assignation to be sure any program is using the device and open a terminal and type:
kal -d 0 -s GSM900 -g 49.6
I look that :
Found 1 device(s):
0: Generic RTL2832U OEM
Using device 0: Generic RTL2832U OEM
usb_claim_interface error -6
Failed to open rtlsdr device #0.
It seems that you are not in OpenPlotter now, are you?
(2020-04-27, 07:40 PM)Sailoog Wrote: [ -> ]It seems that you are not in OpenPlotter now, are you?
i am on openplotter
with rtl_test:
pi @ openplotter: /etc/modprobe.d $ rtl_test
Found 1 device(s):
0: Realtek, RTL2838UHIDIR, SN: 00000001
Using device 0: Generic RTL2832U OEM
usb_claim_interface error -6
Failed to open rtlsdr device #0.
(2020-04-27, 07:53 PM)Romarin Wrote: [ -> ] (2020-04-27, 07:40 PM)Sailoog Wrote: [ -> ]It seems that you are not in OpenPlotter now, are you?
i am on openplotter
with rtl_test:
pi @ openplotter: /etc/modprobe.d $ rtl_test
Found 1 device(s):
0: Realtek, RTL2838UHIDIR, SN: 00000001
Using device 0: Generic RTL2832U OEM
usb_claim_interface error -6
Failed to open rtlsdr device #0.
Do you use an activ hub ? A hub with a current supply. ? The RTL-DSR need some power to work well.
Bram
(2020-04-27, 08:33 PM)verkerkbr Wrote: [ -> ]Do you use an activ hub ? A hub with a current supply. ? The RTL-DSR need some power to work well.
Bram
Yes, I use a separate power supply from RPi4
I blacklist the original drivers.
Now with rtl_test, i have this :
pi@openplotter:~ $ rtl_test
Found 1 device(s):
0: Realtek, RTL2838UHIDIR, SN: 00000001
Using device 0: Generic RTL2832U OEM
Found Rafael Micro R820T tuner
Supported gain values (29): 0.0 0.9 1.4 2.7 3.7 7.7 8.7 12.5 14.4 15.7 16.6 19.7 20.7 22.9 25.4 28.0 29.7 32.8 33.8 36.4 37.2 38.6 40.2 42.1 43.4 43.9 44.5 48.0 49.6
[R82XX] PLL not locked!
Sampling at 2048000 S/s.
Info: This tool will continuously read from the device, and report if
samples get lost. If you observe no further output, everything is fine.
Reading samples in async mode...
Allocating 15 zero-copy buffers
lost at least 160 bytes
^CSignal caught, exiting!
User cancel, exiting...
Samples per million lost (minimum): 3