OpenMarine

Full Version: Signal K not catching Can traffic
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Hello,

I'm lost trying to find what I'm doing wrong.
Let me try to explain what is my problem.

My installation:

    Raspberry PI 4 Model B Rev 1.4 8GB
    PICAN-M with CAN-Bus Micro-C, RS422 connector NME0183, 3A SMPS
    NMEA 2000 test network
    MAIANA CAN version with MAIANA base kit

My configuration:

    Debian GNU/Linux 11 (bullseye) with latest patches
    Architecture aarch64
    openplotter-can/bionic,bionic,now 2.2.2-stable all [installed]
    openplotter-dashboards/bionic,bionic,now 2.2.3-stable all  [installed]
    openplotter-doc/bionic,bionic,now 2.2.1-dev all  [installed]
    openplotter-i2c/bionic,bionic,now 2.2.1-stable all  [installed]
    openplotter-maiana/bionic,bionic,now 2.1.2-stable all  [installed]
    openplotter-network/bionic,bionic,now 2.1.5-stable all  [installed]
    openplotter-opencpn-installer/bionic,bionic,now 2.2.3-stable all  [installed]
    openplotter-serial/bionic,bionic,now 2.2.3-stable all  [installed]
    openplotter-settings/bionic,bionic,now 2.9.1-stable all  [installed]
    openplotter-signalk-installer/bionic,bionic,now 2.4.2-stable all  [installed]

My problem:

    MAIANA device     [Working correctly]
        Catching GPS signal: led for GPS signal green on device when antenna correctly positionned outside
        Device transmitting GPS packets on the CAN bus: packets visible when using candump in command line

    CAN Bus 2.2.2     [Working correctly]
        MCP2512 connection defined correctly: traffic is visible when activating the candump function.
        Connection has been added as "can0" to SignalK.  Tool is displaying correctly the connection identifier.

    Signal K 1.42.00
        "can0" connection is listed correctly with status "Connected to can0"
        Parameters:
            Data type: NMEA2000
            Enabled: Yes
            Logging: Yes
            ID: can0
            NMEA 2000 Source: Canbus (canboatjs)
            Interface: can0
            Use Can NAME in source data: Yes
            Filters: No
            Source Priorities Settings: Empty
        No error reported

        Problem: 
            No connection activity reported. Deltas/second is always at 0 for "defaults" and "can0"
            Total sever Signal K throughput (deltas/second) is always at 0
            In Signal K Instrument panel version 0.22.1 I have only 1 dash "validation. MAIANA" which is always at 0

Can you please help me?
Thanks in advance for your help.

Best regards,
Raoul
You are trying to install OpenPlotter v2.x in Bullseye and it is only for Buster. We are working on OpenPlotter v3.x for Bullseye 32bit and 64bit but we are delayed. I will add this info to docs today, sorry for that.

Your options are:
(2022-05-12, 03:46 PM)Sailoog Wrote: [ -> ]You are trying to install OpenPlotter v2.x in Bullseye and it is only for Buster. We are working on OpenPlotter v3.x for Bullseye 32bit and 64bit but we are delayed. I will add this info to docs today, sorry for that.

Your options are:

Thanks a lot for your answers.
I go for V3 Alpha install and will report any issues encountered trying to help you finalising your release.
Please tell me where my help could be best used.

Best regards,
Raoul
OK, thanks.

Testing and debugging any issue is really helpful right now. Please report here: https://forum.openmarine.net/showthread.php?tid=3878
Working correctly with new installed version.

Installation & test logs prepared for feedback.

You can close this post.