GPS USB-Mouse is no longer recognized by OpenCPN - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: GPS USB-Mouse is no longer recognized by OpenCPN (/showthread.php?tid=1219) Pages:
1
2
|
GPS USB-Mouse is no longer recognized by OpenCPN - waldmattis - 2018-06-07 Good evening regrettably my GPS USB-receiver is not recognized by actual Openplotters OpenCPN. In the previous version all worked fine. The system recognizes the receiver / see listing from lsusb pi@openplotter:~ $ lsusb Bus 001 Device 006: ID 1546:01a5 U-Blox AG NL-402U Bus 001 Device 005: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub pi@openplotter:~ $ The device is Navilock NL-402U In Openplotters previous version it could be found in the NMEA settings. After activating per mouseclick and running diagnostics, the GPS data come in and were used by OpenCPN. In the new version there is no entry for this GPS device. Who knows help_ Regards Karl RE: GPS USB-Mouse is no longer recognized by OpenCPN - jim321 - 2018-06-07 does it show in the serial tab op ? install it there if not. i had a problem with the imu true compass i had to set the pypilot to basic before it was sent to ocpn after update it took a while for my usb gps bu-353 to lock on to a good signal. RE: GPS USB-Mouse is no longer recognized by OpenCPN - waldmattis - 2018-06-08 @jim321 Thank you for Your advice. I checked the serial Tab. I think the GPS is shown there. (when I plug it in and out the list of devices changes) I switched pylot to basic. No GPS Signal at all! The GPS is working fine with - OpenCPN under Windows - Navigatrix (regrettably not available for Raspberry) - OpenCPN under MX Linux So the device is ok. Regards Karl RE: GPS USB-Mouse is no longer recognized by OpenCPN - BlackSea - 2018-06-08 Could you plugin your GPS Maus and copy&paste output messages from following command Code: dmesg RE: GPS USB-Mouse is no longer recognized by OpenCPN - jim321 - 2018-06-08 "I think the GPS is shown there. (when I plug it in and out the list of devices changes) " did you select the one that shows when plugged in and push the auto button or name it and push the apply button. it needs to be installed there before the sys see's it RE: GPS USB-Mouse is no longer recognized by OpenCPN - BlackSea - 2018-06-08 Looks good. Kernel has recognized you GPS Quote:[ 5356.132237] usb 1-1.4: new full-speed USB device number 6 using dwc_otg Now you can test device Code: ls -la /dev/ttyACM0 If you havn't "minicom" Code: aptitude install minicom RE: GPS USB-Mouse is no longer recognized by OpenCPN - waldmattis - 2018-06-08 (2018-06-08, 10:50 AM)jim321 Wrote: "I think the GPS is shown there. @jim321 This advice did it!!! Thank you so much! Now the GPS is working fine again. Now I am going to fix the next problem Getting my AIS by SDR working. Thank you so much again. (2018-06-08, 11:08 AM)BlackSea Wrote: Looks good. Kernel has recognized you GPS@BlackSea Thank you very much for Your efforts to help me. MeanwhileI got it work with advice from jim321 RE: GPS USB-Mouse is no longer recognized by OpenCPN - Sailoog - 2018-06-08 Hopefully one day I will be able to answer RTFM Sorry guys there are still basic stuff that we need to write on the manual. RE: GPS USB-Mouse is no longer recognized by OpenCPN - MilesAhead - 2018-08-02 (2018-06-08, 06:49 PM)Sailoog Wrote: Hopefully one day I will be able to answer RTFM I have a BU-353S4 GPS puck which I managed to configure with OpenCPN so that it reads the GPS data using GPSD. I then set it up to broadcast this information on a local network and the RPI Wifi using UDP. I also have Open CPN running on a Microsoft Surface and Windows desktop and they pick up the GPS data either connected to my home network or to the RPi WiFi. This all works perfectly. However the OpenPlotter documentation states that all NMEA0183, including GPS should go through Kplex. But there is very sparse documentation on how to set up OpenCPN. OpenPlotter instructions for OpenCPN Searching the BB, I came across this thread and followed the instructions, but I just cannot get OP to recognize the GPS puck, so I thought I ask this group for assistance. I unplugged the GPS and rebooted RPi and then plugged in the puck. When I then go into OP, I see the following under Serial. It doesn't matter what I name the GPS, or how i assign it, it still doesn't see to be recognized because I get the same message when i click on auto. However, I assume that the GPS assignment should be Kplex with a baud rate of 4800. When I do this it does appear in Kplex. Notice that I added the UDP settings to broadcast the GPS information across the network at home or on the boat as I did in OpenCPN. However I do not see any messages when I click on Diagnostic in Kplex. I could also not see the arguments of the timeout exception. That is a full window screen grab. So I'm frustrated and confused. Any help would be appreciated greatly. (2018-08-02, 09:57 AM)MilesAhead Wrote:(2018-06-08, 06:49 PM)Sailoog Wrote: Hopefully one day I will be able to answer RTFM RE: GPS USB-Mouse is no longer recognized by OpenCPN - Sailoog - 2018-08-06 You do not have to modify default opencpn settings. Remove all your changes there and create only an input: TCP localhost 10110 You need to do nothing in kplex either. Remove all your manual settings. Assign your GPS in serial tab to GPSD and that is all. Openplotter will send all dat to TCP 10110. |