Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: Bug Reports (https://forum.openmarine.net/forumdisplay.php?fid=4) +--- Thread: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 (/showthread.php?tid=1543) Pages:
1
2
|
RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - jim321 - 2019-03-14 check if communication works i think gps is on tty cat /dev/moitessier.tty check this too just in case i was wrong .. cat /dev/moitessier.spi does this show any errors? dmesg | grep moitessier i dont know whats up with the attachments and picture posting on the site RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - MilesAhead - 2019-03-14 (2019-03-14, 09:13 PM)jim321 Wrote: check if communication works i think gps is on tty Yeah, i was surprised when I looked at the post and could not see the attachments. I'd tried again buy got an error message. They are all JPEG files so I don't know why they cannot be loaded.
RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - jim321 - 2019-03-14 ok those on spi are gps did you do the setup, start in tools "Moitessier HAT" on openplotter ? that's about all i can help you with, i dont have a hat so have never set one up, to be honest today is the first time i have even looked at the tools & setup. RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - MilesAhead - 2019-03-15 (2019-03-14, 10:21 PM)jim321 Wrote: ok those on spi are gps Thx for the help Jim, much appreciated. Yes, I went through all the config pages for the Moitessier HAT in the V1.x.x OpenPlotter docs. I think it is more of an issue at the Raspbian level, but I am far from an expert. I'm using an RPi 3b+ and there is a whole host of info on the internet about getting GPSD to work correctly with GPS USB pucks. And when I look at my /etc/default/gpsd it looks like the daemon isn't even started.
When I run
There are no instructions on either the OP or Moitessier web sites on how to set this up. Frustrating!! Any thoughts? RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - jim321 - 2019-03-15 "I get output for both, but the GSA and GLL messages do not contain any lat/lon info." antenna ? clear view of the sky? have you checked the serial tab to see if it needs config there.? pushed the start tab in tools ? like i said i am not familiar with the setup.. Download PDF https://www.rooco.eu/wp-content/uploads/2018/11/Moitessier_HAT_User_Guide_v0.2.pdf RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - MilesAhead - 2019-03-15 (2019-03-15, 10:10 AM)jim321 Wrote: "I get output for both, but the GSA and GLL messages do not contain any lat/lon info." Hi Jim Yes, been through the doc several times. I've asked the rooco guys too. Regards Trevor RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - jim321 - 2019-03-15 well i just read it and seems pretty straightforward to me it's just like you have to do when using everything separate gps imu i2c set up the serial tab.. setup pypilot tab setup i2c tab chapter 8.2 thru 8.7 in user manual.. RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - MilesAhead - 2019-03-15 Yes, I've done all that, and the pressure, heel, yaw, temperature, ... are all working. It is just the GPS/GNSS that is not. I looked at the "cat /dev/moitessier.tty" output some more and there are clearly several satellites in view. $GPGSV,3,1,11,07,81,272,,08,71,064,,30,46,306,30,11,40,165,,0*63 $GPGSA,A,1,,,,,,,,,,,,,,,,1*03 $GPGLL,,,,,204350.000,V,N*7A When I run "cat /dev/moitessier.spi" I see the following: $GPGSV,3,1,11,07,82,240,,08,67,058,,30,51,304,29,11,45,163,,0*66 $GNGSA,A,2,78,,,,,,,,,,,,44.39,44,38,1.0,2*0C $GNGLL,4323.3890,N,07942.6931,W,205432.000,A<A*56 So clearly there are some reading coming from what I presume to be the GNSS, but there doesn't seem to be anything from the GPS. RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - jim321 - 2019-03-16 it needs to be setup to be one or the other gpsd or gps not both..with a clear view of the sky. gpsd is a daemon that receives data from a GPS receiver, and provides the data back to multiple applications such as Kismet or GPS navigation software. It thus provides a unified interface to receivers of different types, and allows concurrent access by multiple applications. GNSS GNSS stands for Global Navigation Satellite System, and is the standard generic term for satellite navigation systems that provide autonomous geo-spatial positioning with global coverage. This term includes e.g. the GPS, GLONASS, Galileo, Beidou and other regional systems. GNSS is a term used worldwide The advantage to having access to multiple satellites is accuracy, redundancy and availability at all times. Though satellite systems don't often fail, if one fails GNSS receivers can pick up signals from other systems. Also if line of sight is obstructed, having access to multiple satellites is also a benefit. Common GNSS Systems are GPS, GLONASS, Galileo, Beidou and other regional systems. GPS The United States' Global Positioning System (GPS) consists of up to 32 medium Earth orbit satellites in six different orbital planes, with the exact number of satellites varying as older satellites are retired and replaced. Operational since 1978 and globally available since 1994, GPS is currently the world's most utilized satellite navigation system. RE: Moitessier HAT firmware update failed after update to OpenPlotter 1.2 - MilesAhead - 2019-03-16 (2019-03-16, 09:40 AM)jim321 Wrote: it needs to be setup to be one or the other gpsd or gps not both..with a clear view of the sky. Hi Jim, did I thank you for your help lately? And for your patience? Much appreciated. I'm not sure where you mean the setup needs to happen - "gpsd or gps"? Do you mean in Raspbian or in OP on the Serial tab?
As a side note the USB GPS puck and the Moitessier HAT puck are sitting side-by-side on my window shelf, so they are getting the identical signal. |