Connecting NMEA Wind data from NASA Clipper - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: Connecting NMEA Wind data from NASA Clipper (/showthread.php?tid=1116) |
RE: Connecting NMEA Wind data from NASA Clipper - Smartell - 2018-06-21 I have a Freeboard somewhere and that has nmea seatalk conversion using an arduino so the code exists (never tried it though). I think that rob42 on github knows more. /M RE: Connecting NMEA Wind data from NASA Clipper - PaddyB - 2018-06-22 Just a quick one sort of relavent - I've just got an esp sending data from a nasa compass straight to signalk using the tinygps++ library , software serial and and EspSigk with a rs232/ttl adaptor powered from the esp 3.3v pin - I'll leave it on all day to see if it breaks With HDG selected in the conver to NMEA plugin the data shows up in Opecnn dashboard and gets automatically entered into the logbook. Turned off the security to allow the data in , but think Sbender is going to sort this - https://signalk-dev.slack.com/archives/C9B4Y02EN/p1529631013000074 rough and ready code > Code: #include <TinyGPS++.h> RE: Connecting NMEA Wind data from NASA Clipper - Smartell - 2018-06-22 (2018-06-22, 12:33 PM)PaddyB Wrote: Just a quick one sort of relavent - I've just got an esp sending data from a nasa compass straight to signalk using the tinygps++ library , software serial and and EspSigk with a rs232/ttl adaptor powered from the esp 3.3v pin - I'll leave it on all day to see if it breaks Doing this wireless? ...wireless Nmea? RE: Connecting NMEA Wind data from NASA Clipper - PaddyB - 2018-06-22 (2018-06-22, 04:50 PM)Smartell Wrote: Doing this wireless? ...wireless Nmea? Taking the NMEA data from a nasa compass and sending it to openplotter as Signalk. RE: Connecting NMEA Wind data from NASA Clipper - Sailoog - 2018-06-26 I guess this post is relevant for this. https://groups.google.com/forum/#!topic/kplex/4LN2K52LN5M There are 2 solutions on for kplex and one for signal k RE: Connecting NMEA Wind data from NASA Clipper - Smartell - 2018-06-27 (2018-06-26, 06:14 PM)Sailoog Wrote: I guess this post is relevant for this. Hi, Yes, i posted my question also in that group and it seems people are helpful there too. I will test it on my setup this weekend. Appreciate your support! /Micael RE: Connecting NMEA Wind data from NASA Clipper - Smartell - 2018-06-30 Now i have the NASA mast unit feeds working also without the Node Red setup. I checked the answers to my post generated in the Kplex Google group (any nudging there Paddy?) and i tried adding strict=0 in my config file and it worked like a charm (after some cleaning up after earlier efforts) I have been bitten by Node Red though and will probably fiddle around a lot with that - incredibly powerful! So...SeaTalk, modifying SailGauge w larger numbers so i can read it, moving everything into a seaworhy box...and i am done. Well, not done, i guess you will never be done with something like this..."i will be back" Thanks! RE: Connecting NMEA Wind data from NASA Clipper - jim321 - 2018-06-30 "i tried adding strict=0 in my config file" where is the config file located? RE: Connecting NMEA Wind data from NASA Clipper - Smartell - 2018-06-30 (2018-06-30, 04:24 PM)jim321 Wrote: "i tried adding strict=0 in my config file" Click on the "Advanced" tab above and then you will see the definition blocks in the config file. add strict=no somewhere in- the serial input you have defined for your device /M RE: Connecting NMEA Wind data from NASA Clipper - jim321 - 2018-06-30 Thanks in v.1.0.X its Kplex tab. that screen shot must be v.0.1.X i put it at the end.. |