Server Hardware for openplotter? - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Server Hardware for openplotter? (/showthread.php?tid=1807) |
RE: Server Hardware for openplotter? - Max1947 - 2019-12-02 (2019-12-02, 01:37 PM)glowntiger Wrote: Hi, Hi, explain ... do I have to uninstall your app and clone the new one? Fixed Linux driver? RE: Server Hardware for openplotter? - glowntiger - 2019-12-03 Hi Max, go on your Pi and type: Code: sudo rm -r openplotter-MCS to delete the folder. then load the new git data: Code: git clone https://github.com/Thomas-GeDaD/openplotter-MCS Code: cd openplotter-MCS and install: Code: sudo python3 setup.py install now you can start the openplotter APP: PHP Code: openplotter-MCS there is a new service in the background (openplotter-MCS-asd) if you enable the autoshutdown in the app, the Pi shuts down after power off the +12V enable Terminal. You must one time start the app and push save for starting the Service. Until now the app is not handle by openplotter... I hope sailoog do this the next time. The driver issue is a timing problem of the adresses. I have change the adress of the third sc16is752 on the hardware side. I have order 20 new MCS an they should arrived the next days. At the moment you can only use 4 of the 6 NMEA0183 ports. All who have get a prototype board gets a new MCS if availible.... https://github.com/raspberrypi/linux/issues/3340 here you find info´s to the issue RE: Server Hardware for openplotter? - Max1947 - 2019-12-03 (2019-12-03, 09:07 AM)glowntiger Wrote: Hi Max, Hi, I followed the instructions but I must have been wrong, see photo. I book for the new card and I hope that in the meantime Sailoog and Rocco make progress. I hope everything is ready for spring and try it all on my boat. Ok, winter is still long, there's time ... good job everyone! [img][/img] [img][/img] RE: Server Hardware for openplotter? - glowntiger - 2019-12-03 Hi Max, Sorry i have missed two "". Please try again. The same procedure…. Why you have add a ventilation? It´s not needed… You did not get temperature problems… But looks good… RE: Server Hardware for openplotter? - Max1947 - 2019-12-03 (2019-12-03, 05:37 PM)glowntiger Wrote: Hi Max, Ok, I repeated everything a couple of times and now it's all right. More than the fan (which is actually not needed) I wanted to see the various LEDs to make sure that it was working properly. I had this available and can temporarily go! I also added the switch ... RE: Server Hardware for openplotter? - glowntiger - 2019-12-03 Did the pi shut Down? RE: Server Hardware for openplotter? - Max1947 - 2019-12-03 (2019-12-03, 08:12 PM)glowntiger Wrote: Did the pi shut Down? Ciao, guarda: [img][/img] RE: Server Hardware for openplotter? - glowntiger - 2019-12-05 Hi MAx, Sorry I have forgotten one step. The Installation.... Do: Code: sudo MCSPreUninstall Code: sudo MCSPostInstall Without the Service isn´t availible RE: Server Hardware for openplotter? - Max1947 - 2019-12-05 (2019-12-05, 09:12 AM)glowntiger Wrote: Hi MAx, RE: Server Hardware for openplotter? - glowntiger - 2019-12-07 Did the shutdown work at your configuration? |