+- OpenMarine (https://forum.openmarine.net)
+-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1)
+--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2)
+--- Thread: Server Hardware for openplotter? (/showthread.php?tid=1807)
RE: Server Hardware for openplotter? - glowntiger - 2020-04-16
Hi,
all ordered packages are on their way. Sorry for the delay.
Now are enough in stock... ;-)
@max:
I send it to you next time... ;-)
RE: Server Hardware for openplotter? - Max1947 - 2020-04-16
Ok Thomas, thanks!
For Italian users I attach the translated QuickGuide. Good wind and stay at home again ... we will make beautiful sailing before long!
(Ok Thomas, grazie!
Per gli utenti italiani allego la QuickGuide tradotta. Buon vento e restate in casa ancora...faremo belle veleggiate fra non molto!)
RE: Server Hardware for openplotter? - Max1947 - 2020-04-22
Hi Thomas, the new card has arrived, thank you. I connected the Clipper Wind, the led on the MCS is steady red (does not flash). Notify me when you want to connect with anidesk for posting.
RE: Server Hardware for openplotter? - Bill_ Maxwell - 2020-04-22
Hi Thomas
Are you able to send the server board to Australia yet?
Bill
RE: Server Hardware for openplotter? - glowntiger - 2020-04-23
Hi Bill,
i have add Australia (Australien in German) to the shipping targets on the website.
Shipping cost is a little bit higher... :-( (48€)
Don´t know how long the shipping needs in the Moment. I send out parts in 1-2 days...
RE: Server Hardware for openplotter? - Bill_ Maxwell - 2020-04-23
Viele Danke, Thomas.
RE: Server Hardware for openplotter? - Max1947 - 2020-04-23
Ok Thomas, thanks for your work. Now everything works perfectly. I hope the SignalK managers will make the adjustment after your request. Good wind to you and the whole OP group!
RE: Server Hardware for openplotter? - flybob - 2020-04-23
I got the board yesterday, finally! Mounted in in the boat and tried to boot up - nothing. However seems like the ribbon cable was a bit loose which was fixed at home later. So now it's booting and should work just fine.
However - the Moitessier hat cannot be mounted without an extra pin head and it's quite tricky to come by actually! Not a lot of places ship to Sweden these days so I've been hunting online for a couple of hours(!) for something as simple as a gpio duplicator with reasonable shipping time. Would be a great accessory to your shop glowntiger
RE: Server Hardware for openplotter? - Max1947 - 2020-04-23
(2020-04-23, 07:30 PM)flybob Wrote: I got the board yesterday, finally! Mounted in in the boat and tried to boot up - nothing. However seems like the ribbon cable was a bit loose which was fixed at home later. So now it's booting and should work just fine.
However - the Moitessier hat cannot be mounted without an extra pin head and it's quite tricky to come by actually! Not a lot of places ship to Sweden these days so I've been hunting online for a couple of hours(!) for something as simple as a gpio duplicator with reasonable shipping time. Would be a great accessory to your shop glowntiger
Hi, is this what you are looking for? https://www.amazon.com/Connectors-Raspberry-40-pin-Expansion-RAS-GP02/dp/B07MCW4KCM/ref=sr_1_51?keywords=40+pin+connector&qid=1570444309&sr=8-51
However Thomas should have them!
RE: Server Hardware for openplotter? - jamieFL - 2020-04-25
Please forgive me. I've reviewed the first few and last few pages and this looks very promising. Can the OP please update the first post, or provide a link to where the most up-to-date information about this project seen.