Server Hardware for openplotter? - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Server Hardware for openplotter? (/showthread.php?tid=1807) |
RE: Server Hardware for openplotter? - glowntiger - 2019-10-06 In principle yes, but the adapter is not ready until now. If all runs well, i make the adapter. The pins of the moitessier and the MCS are compatible. (2019-10-06, 02:30 PM)jim321 Wrote: the 40 pin header could be changed to a stackable one with the socket on the back for the pi and pins on front to plug in the Moitessier hat. ? Yes, but until now i did not find one. ? RE: Server Hardware for openplotter? - Sailabout - 2019-10-06 The Moitessier hat also uses some pins exclusively. any possible conflict? RE: Server Hardware for openplotter? - glowntiger - 2019-10-06 (2019-10-06, 03:17 PM)Sailabout Wrote: The Moitessier hat also uses some pins exclusively. any possible conflict? No, i have only used pins which are free... i2c was shared. There should be no address conflict if I had study the manual right.... spi I used ce2. RE: Server Hardware for openplotter? - Max1947 - 2019-10-06 (2019-10-06, 03:35 PM)glowntiger Wrote:(2019-10-06, 03:17 PM)Sailabout Wrote: The Moitessier hat also uses some pins exclusively. any possible conflict? Well I saw the progress, as I said I wait for you to tell me when everything is ready. The new card is perfect. Good job. OP2 is moving forward and I hope the Beta version will arrive soon. Great job Sailoog! RE: Server Hardware for openplotter? - glowntiger - 2019-10-07 Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins) Until I get a Moitessier hat I will check if all works fine together... RE: Server Hardware for openplotter? - Max1947 - 2019-10-07 (2019-10-07, 07:58 AM)glowntiger Wrote: Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins) Can help? :https://www.amazon.com/40-pin-connector/s?k=40+pin+connector RE: Server Hardware for openplotter? - glowntiger - 2019-10-07 (2019-10-07, 10:10 AM)Max1947 Wrote:(2019-10-07, 07:58 AM)glowntiger Wrote: Here you see the used Pins of the MCS-board: (in Black the Moitessier Pins) Yes, after some search I have found one. This should work: https://www.amazon.com/Connectors-Raspberry-40-pin-Expansion-RAS-GP02/dp/B07MCW4KCM/ref=sr_1_51?keywords=40+pin+connector&qid=1570444309&sr=8-51 Then I only need longer distance adapter to moitessier hat.... I have ordered some to check. Now I only need a moitessier hat Has anybody a moitessier hat and want to check if all works fine now? RE: Server Hardware for openplotter? - jim321 - 2019-10-07 https://www.aliexpress.com/item/32868096740.html?spm=a2g0o.productlist.0.0.63fb489fAevlYe&algo_pvid=b3cbff7c-ebd1-4d12-9bf0-0f262851d3bb&algo_expid=b3cbff7c-ebd1-4d12-9bf0-0f262851d3bb-0&btsid=c14503f7-8c58-449c-a75d-1251c382af19&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_52 if the female header is on top to plug the hat, and the pi on the other side of board to pins stacked together no cable needed RE: Server Hardware for openplotter? - Max1947 - 2019-10-07 (2019-10-07, 11:57 AM)glowntiger Wrote:(2019-10-07, 10:10 AM)Max1947 Wrote:(2019-10-07, 07:58 AM)glowntiger Wrote: Qui puoi vedere i Pin usati della scheda MCS: (in Black the Moitessier Pins) Ciao, ho il Moitessier ma non so come fare i controlli. Ho tutto a casa, non sulla barca. Se posso essermi utile e spiegarmi, puoi inviarmi la scheda e i vari accessori per la connessione. Potrei collegare un "A5130 autonnico con uscita NMEA-2000" (vedi: https://www.autonnic.com/marine-industrial-sensors) un sensore di temperatura DS18B20 e anche un sensore del vento NMEA 0183 MWV "NASA Marine Clipper" " Dammi il costo della carta anche in PM, e ti pagherò, ma come ho detto, non essendo un elettronico, devi dirmi cosa fare per le connessioni, ecc. Aspetto notizie e ti saluto . Ancora una volta, se questo adattatore può essere utile per la tua carta: Adathttps://www.sg-electronic-systems.com/ecommerce/can-bus-shield/21-quad-can-adapter-quad-can-bus-is-an-open-hardware-to-connect-a-couple-of-canber-boards-to-raspberry-pi-in-this-way-it-is-possi.htmltatore RE: Server Hardware for openplotter? - jim321 - 2019-10-07 after a closer look the 12v area could interfere with the compass on the Moitessier hat.so a cable would move it away from that. i guess it will need to be tested ..hope it works. |