Getting Moitessier pressure / temp - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2) +--- Thread: Getting Moitessier pressure / temp (/showthread.php?tid=2384) Pages:
1
2
|
Getting Moitessier pressure / temp - fishy - 2020-02-27 All seems to work fine (latest NOOBS) however I can not get any pressure / temp data from the Moitessier.. The config is pretty much vanilla. In I2C both pressure and temperature sensors are defined, both from the wane sensor: MS5607-02BA03 with address 0x77. Also in I2C, connections, there are 2 entries: the sensor MS5607-02BA03 has a port 51000 connection to SK, name I2C. The second SK connection is port 20220, no sensor defined, named Pypilot Signal K. In Signal K both connections are listed and enabled, type SignalK, no logging. In the new (thank you!) Diagnostic Signal K window I see 4 I2C entries: roll, pitch yaw and magnetic. These come from OpenPlotter.I2C.pypilot. I do not see any environment (outsdide temperature, outside pressure) I have not messed around with these settings yet- should I have?? Thanks for your help! RE: Getting Moitessier pressure / temp - Sailoog - 2020-02-27 in settings app update candidates, sources if demanded and install latest versions of all apps. Reboot and go to SK server dashboard. Is I2C connection getting data? RE: Getting Moitessier pressure / temp - fishy - 2020-02-27 (2020-02-27, 06:15 PM)Sailoog Wrote: in settings app update candidates, sources if demanded and install latest versions of all apps. Thanks for your time! Just checked, had latest version of everything (I2C 2.0.7-stable, SignalK 2.0.10-stable) not getting anything on hte I2C connection in SignalK.. (I2C 0 (0%)) the input I2C is configured as follows: Input type: SignalK Enabled: yes Logging: No ID: I2C SignalK Source: UDP Port: 51000 As far as I can tell this matches the I2C config... RE: Getting Moitessier pressure / temp - Sailoog - 2020-02-27 remove the sensor from the I2C app and go to moitessier app. click on "check pressure", what happens? RE: Getting Moitessier pressure / temp - fishy - 2020-02-27 (2020-02-27, 07:06 PM)Sailoog Wrote: remove the sensor from the I2C app and go to moitessier app. Temp is OK, pressure gives me en empty </> window.. It's on driver version 4.19.97_1.6.0 Configuration check for Pressure - Temperature: I2C - Signal K key for pressure: none I2C - Signal K key for temperature: none Connection: not connected System check: Moitessier HAT is attached. I2C is enabled. SPI is enabled. Moitessier HAT package is installed. Package: moitessier Status: install ok installed Maintainer: Thomas POMS <hwsw.development@gmail.com> Architecture: armhf Version: 1.6.0 Description: Moitessier HAT (AIS/GNSS navigation) This package provides all the relevant tools, binaries and scripts to communicate, control and update the Moitessier HAT. Homepage: https://www.rooco.eu <edit> After re-adding the sensor to I2C, the config for Pressure - Temperature is again: I2C - Signal K key for pressure: environment.outside.pressure I2C - Signal K key for temperature: environment.outside.temperature Connection: Signal K connection ID = I2C Signal K to NMEA 0183 plugin: enabled Pressure conversion: enabled </edit> Lemon? RE: Getting Moitessier pressure / temp - fishy - 2020-03-01 Found the culprit- the address for my sensor was not 0x77 but 0x68 Thanks again PS That said- I now get a pressure of 1.7 hPa (in OpenCPN), and 170.794 Pa in SignalK diagnostic. Not very realistic values, and it's not changing at all.... Any hints on configuring this? It's not a core requirement, but It'd be nice to have a graph of pressure... Not getting any temp value that makes sense, at all.. Help appreciated.. RE: Getting Moitessier pressure / temp - Sailoog - 2020-03-02 The address for the pressure and temperature sensors in Moitessier HAT is 0x77. 0x68 is the IMU address. RE: Getting Moitessier pressure / temp - fishy - 2020-03-02 (2020-03-02, 03:18 PM)Sailoog Wrote: The address for the pressure and temperature sensors in Moitessier HAT is 0x77. Sadly, then I am getting nothing.<edit> 77 is not even listed as a port in I2C</edit> Is there a way to test the sensor? The Moitessier app only gives met an empty </> tab, not even an error message... RE: Getting Moitessier pressure / temp - Sailoog - 2020-03-03 That is strange. Please ask to rooco guys here: https://www.rooco.eu/questions-answers-moitessier-hat/ RE: Getting Moitessier pressure / temp - fishy - 2020-03-06 Thanks Sailoog- did just that. Turns out htere is a test script in the moitessier folder: check_functionality --all in my case, it returns ********** CPU ********** 48.199 ********** MS5607-02BA03 ********** Reading PROM failed. ERROR: Reading sensor failed. This might be okay, if this sensors is not assembled on the board. Seems it's a hardware problem |