Signal K not catching Can traffic - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: Signal K not catching Can traffic (/showthread.php?tid=4044) |
Signal K not catching Can traffic - ALROCHARARI - 2022-05-12 Hello, I'm lost trying to find what I'm doing wrong. Let me try to explain what is my problem. My installation: Raspberry PI 4 Model B Rev 1.4 8GB PICAN-M with CAN-Bus Micro-C, RS422 connector NME0183, 3A SMPS NMEA 2000 test network MAIANA CAN version with MAIANA base kit My configuration: Debian GNU/Linux 11 (bullseye) with latest patches Architecture aarch64 openplotter-can/bionic,bionic,now 2.2.2-stable all [installed] openplotter-dashboards/bionic,bionic,now 2.2.3-stable all [installed] openplotter-doc/bionic,bionic,now 2.2.1-dev all [installed] openplotter-i2c/bionic,bionic,now 2.2.1-stable all [installed] openplotter-maiana/bionic,bionic,now 2.1.2-stable all [installed] openplotter-network/bionic,bionic,now 2.1.5-stable all [installed] openplotter-opencpn-installer/bionic,bionic,now 2.2.3-stable all [installed] openplotter-serial/bionic,bionic,now 2.2.3-stable all [installed] openplotter-settings/bionic,bionic,now 2.9.1-stable all [installed] openplotter-signalk-installer/bionic,bionic,now 2.4.2-stable all [installed] My problem: MAIANA device [Working correctly] Catching GPS signal: led for GPS signal green on device when antenna correctly positionned outside Device transmitting GPS packets on the CAN bus: packets visible when using candump in command line CAN Bus 2.2.2 [Working correctly] MCP2512 connection defined correctly: traffic is visible when activating the candump function. Connection has been added as "can0" to SignalK. Tool is displaying correctly the connection identifier. Signal K 1.42.00 "can0" connection is listed correctly with status "Connected to can0" Parameters: Data type: NMEA2000 Enabled: Yes Logging: Yes ID: can0 NMEA 2000 Source: Canbus (canboatjs) Interface: can0 Use Can NAME in source data: Yes Filters: No Source Priorities Settings: Empty No error reported Problem: No connection activity reported. Deltas/second is always at 0 for "defaults" and "can0" Total sever Signal K throughput (deltas/second) is always at 0 In Signal K Instrument panel version 0.22.1 I have only 1 dash "validation. MAIANA" which is always at 0 Can you please help me? Thanks in advance for your help. Best regards, Raoul RE: Signal K not catching Can traffic - Sailoog - 2022-05-12 You are trying to install OpenPlotter v2.x in Bullseye and it is only for Buster. We are working on OpenPlotter v3.x for Bullseye 32bit and 64bit but we are delayed. I will add this info to docs today, sorry for that. Your options are:
RE: Signal K not catching Can traffic - ALROCHARARI - 2022-05-12 (2022-05-12, 03:46 PM)Sailoog Wrote: You are trying to install OpenPlotter v2.x in Bullseye and it is only for Buster. We are working on OpenPlotter v3.x for Bullseye 32bit and 64bit but we are delayed. I will add this info to docs today, sorry for that. Thanks a lot for your answers. I go for V3 Alpha install and will report any issues encountered trying to help you finalising your release. Please tell me where my help could be best used. Best regards, Raoul RE: Signal K not catching Can traffic - Sailoog - 2022-05-12 OK, thanks. Testing and debugging any issue is really helpful right now. Please report here: https://forum.openmarine.net/showthread.php?tid=3878 RE: Signal K not catching Can traffic - ALROCHARARI - 2022-05-12 Working correctly with new installed version. Installation & test logs prepared for feedback. You can close this post. |