OpenMarine
set a GPIO Output to 1 - Printable Version

+- OpenMarine (https://forum.openmarine.net)
+-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1)
+--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3)
+--- Thread: set a GPIO Output to 1 (/showthread.php?tid=4765)

set a GPIO Output to 1 - tobias.e - 2023-07-16

Hi everybody, 

i am trying to set up a Pi Zero2, and it almost works for me. I installed a vanilla raspbian image and added the openplotter repo to it.

One thing i am struggling with is setting an GPIO output. My config.txt contains "gpio=20=op,dh", but during (and after) bootup, the output of PIN38 is 0:

Code:
pi@pizero2:~ $ gpio readall
+-----+-----+---------+------+---+Pi Zero 2W+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
|     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
|   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5v      |     |     |
|   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
|   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 1 | ALT0 | TxD     | 15  | 14  |
|     |     |      0v |      |   |  9 || 10 | 1 | ALT0 | RxD     | 16  | 15  |
|  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
|  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
|  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
|     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
|  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
|   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 0 | IN   | GPIO. 6 | 6   | 25  |
|  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
|     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
|   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
|   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
|   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
|  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
|  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
|  26 |  25 | GPIO.25 |   IN | 0 | 37 || 38 | 0 | OUT  | GPIO.28 | 28  | 20  |
|     |     |      0v |      |   | 39 || 40 | 1 | IN   | GPIO.29 | 29  | 21  |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
+-----+-----+---------+------+---+Pi Zero 2W+---+------+---------+-----+-----+
when i set the output to 1, it stays 1 for a second, then goes back to zero. Any ideas, where i could be looking for something that writes these zeros?

RE: set a GPIO Output to 1 - baltika_no_9 - 2023-07-16

EDIT - I tried GPIO 20 on my Pi 4 and can't set that to high either. Must be something about that particular pin as others work ok. It seems to be a designated digital audio input pin.

RE: set a GPIO Output to 1 - tobias.e - 2023-07-24

Tanks for that hint!

I recently die a very  minimalistic re-install (propably without sound-related stuff) and  now it works just finde.