Posts: 47
Threads: 1
Joined: Feb 2020
Reputation:
0
thank you very much. Ok for the data that the i60 must receive through nmea 2000: example the boat speed, if the boat is stopped, should the i60 display the true wind or will it display 0 as true wind? i60 calculates true wind by receiving speed and apparent wind.
Comet 1000 - Openplotter under construction
Posts: 181
Threads: 4
Joined: May 2018
Reputation:
28
It will show as true and apparent wind the same speed... ;-)
Posts: 47
Threads: 1
Joined: Feb 2020
Reputation:
0
(2020-06-02, 01:17 PM)glowntiger Wrote: It will show as true and apparent wind the same speed... ;-)
Nothing. Instead of showing True Wind, it only shows dashes (_ _ _ _). Like when the i60 is not connected via N2K, which in this case is logical not receiving the boat speed. Do I have to set and what in Signal K (Plug in Signal k to N2000)?
Comet 1000 - Openplotter under construction
Posts: 181
Threads: 4
Joined: May 2018
Reputation:
28
Have you enable the signalk to nmea2000? How do you translate? Have you config signalk?
Posts: 47
Threads: 1
Joined: Feb 2020
Reputation:
0
2020-06-03, 07:54 AM
(This post was last modified: 2020-06-03, 07:58 AM by niklun.)
(2020-06-02, 05:02 PM)Max1947 Wrote: (2020-06-02, 04:03 PM)niklun Wrote: (2020-06-02, 01:17 PM)glowntiger Wrote: It will show as true and apparent wind the same speed... ;-)
Nothing. Instead of showing True Wind, it only shows dashes (_ _ _ _). Like when the i60 is not connected via N2K, which in this case is logical not receiving the boat speed. Do I have to set and what in Signal K (Plug in Signal k to N2000)?
Hi, I sent you some photos! Open your mail!
https://i.imgur.com/VmbGqbD.png
Grazie Max, molto gentile. Ho letto e visto le immagini. Infatti adesso riesco a riceve dati dal i60, ma, pur attivando wind su signK to n2k niente non riceve. Bho
Thanks Max, very kind. I have read and seen the images. In fact, now I can receive data from the i60, but, even if I activate wind on signK to n2k, nothing does not receive. bho
(2020-06-02, 07:32 PM)glowntiger Wrote: Have you enable the signalk to nmea2000? How do you translate? Have you config signalk?
Yes, I am configuring SignK but I go at random .... by attempts, without a guide or preparation my efforts are random. It would be nice to have a beginner's guide for software configuration. Thanks anyway to everyone for what you are doing.
Comet 1000 - Openplotter under construction
Posts: 47
Threads: 1
Joined: Feb 2020
Reputation:
0
Glowtiger ..., I noticed another problem: it happened to me that after a while of using the system, a message appeared at power on with an alert (failed to start load kernel modules ....). then again after a while the signK server went into crisis and then paypilot no longer worked .... in short, a mess. I have reinstalled the whole system for 3/4 times ...... but always the same after a bit of accents. Yesterday I reinstalled, I marked everything I did in the settings until I found out when the disturbances began. At the first shutdown through the enable on 12V with switch. It seems that the shutdown of the RPI does not happen correctly and that the kernel is corrupted .... and then it doesn't work anymore. Example now the atmospheric pressure and temperature are not working through the hat (i2c of the hat). Do you have solutions?
Comet 1000 - Openplotter under construction
Posts: 181
Threads: 4
Joined: May 2018
Reputation:
28
Hi niklun,
do not know you exactly system setting....
Have you enable the autoshutdown mode in the MCS APP before you have use this mode as described in the Manual?
If you have not enable this widget, the pi stops hard... !!!