This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
problem installing moitessier firmware [closed]
#11
I really tried both packages, same result: https://i.imgur.com/a3u0pGc.png  Huh
#12
Can you access the HAT after a reboot?
#13
yes, 
check config results

AIS - GNSS
Device: /dev/moitessier.tty
Connection: 
App = Signal K, Device = /dev/ttyOP_wind, ID = wind, Status = enabled
App = Signal K, Device = /dev/ttyOP_can, ID = can, Status = enabled
Compass - Trim - Heel
Pypilot mode: only compass
Connection: Signal K connection ID = Pypilot Signal K
Signal K to NMEA 0183 plugin: disabled
   Heading conversion: disabled
   Trim - Heel conversion: disabled
Pressure - Temperature
I2C - Signal K key for pressure: environment.outside.pressure
I2C - Signal K key for temperature: environment.inside.openplotter.temperature
Connection: Signal K connection ID = I2C
Signal K to NMEA 0183 plugin: disabled
   Pressure conversion: disabled
Richard

Alberg 30 #597 on Lake of Two Mountains, Quebec, Canada
#14
(2020-07-28, 08:29 PM)Rooco Wrote: Can you access the HAT after a reboot?

Yes, but yes nothing "serial":

https://i.imgur.com/1JJoeFu.png

https://i.imgur.com/9906XGR.png

https://i.imgur.com/4rqNkTQ.png

https://i.imgur.com/D8NsnDw.png
#15
no, in serial I only see the ttyAMA0, that is probably the UART
I get the i2c from the hat, only, ais and gps are undetected
Richard

Alberg 30 #597 on Lake of Two Mountains, Quebec, Canada
#16
If I cannot use the Moitessier HAT as GPS receiver with Buster and Raspi 3b or 4, What can I do ?

If it can work with usb gps receiver, what could be the recommandation ?

Then I might completely remove the Moitessier HAT since it uses power and becomes mostly useless...
Richard

Alberg 30 #597 on Lake of Two Mountains, Quebec, Canada
#17
Just to ensure, have you installed the following package?
https://get.rooco.tech/moitessier/buster..._armhf.deb

The error is caused if you use a wrong package.

Do the following:

wget https://get.rooco.tech/moitessier/buster..._armhf.deb
sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb
#18
(2020-07-29, 06:56 PM)Rooco Wrote: Just to ensure, have you installed the following package?
https://get.rooco.tech/moitessier/buster..._armhf.deb

The error is caused if you use a wrong package.

Do the following:

wget https://get.rooco.tech/moitessier/buster..._armhf.deb
sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb

Sorry, I'm not a technician, just copy / paste. Where am I wrong? 

https://i.imgur.com/EmvCz0p.png
#19
Unfortunately the forum software obviously shortens the link, so it is invalidated.

Click on the link and save the file on your Pi. Then you can skip the wget command.
#20
Thanks @nebosa e @Rooco meanwhile I have another sd with 4.19.97 kernel fully functional ... the latter makes me crazy.  Angry Huh

see: https://i.imgur.com/mP6i9t8.png

https://i.imgur.com/1JJoeFu.png


Forum Jump:


Users browsing this thread: 2 Guest(s)