This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CLOSED] No activity and data in signal K for USB/NMEA but logfiles get them
#1
Bug 
Hi,
I have connected my nmea 0183 loch datas: depth, wtaer temp, ... and logfile is ok for my device:
1597175775146;N;$VWVHW,,,,,00.0,N,00.0,K
1597175775146;N;$PTTKV,00.0,A,00.0,03339.0,00882.7,28.1,C
1597175775147;N;$PTTKD,003.8,A,B
1597175775147;N;$VWVLW,03339.0,N,00882.7,N
1597175775148;N;$VWMTW,28.1,C
1597175775148;N;$SDDPT,003.8,+0.0
1597175775312;N;$SDDBT,012.8,f,003.8,M,002.1,F


But nothing in signal K web app (dashboard, databrowser, ...).

For my wind data, everything works fine: log files and dash board and databrowser,...).

Bug ?
Thanks in advance for your help (last version of openplotter installed with signal K 1.26)

Best regards
Philippe
Reply
#2
(2020-08-11, 09:20 PM)Phil Wrote: Hi,
I have connected my nmea 0183 loch datas: depth, wtaer temp, ... and logfile is ok for my device:
1597175775146;N;$VWVHW,,,,,00.0,N,00.0,K
1597175775146;N;$PTTKV,00.0,A,00.0,03339.0,00882.7,28.1,C
1597175775147;N;$PTTKD,003.8,A,B
1597175775147;N;$VWVLW,03339.0,N,00882.7,N
1597175775148;N;$VWMTW,28.1,C
1597175775148;N;$SDDPT,003.8,+0.0
1597175775312;N;$SDDBT,012.8,f,003.8,M,002.1,F


But nothing in signal K web app (dashboard, databrowser, ...).

For my wind data, everything works fine: log files and dash board and databrowser,...).

Bug ?
Thanks in advance for your help (last version of openplotter installed with signal K 1.26)

Best regards
Philippe

Your logfile messages don't have checksums, they should look like this >
$VWVHW,,,,,00.0,N,00.0,K*4D

If you can't get the devices to send with a checksum then in the signalk connection set validate checksum to no and append checksum to yes. Though not all messages are decoded into signalk 
https://github.com/SignalK/signalk-parser-nmea0183
Reply
#3
Hi, great, you were right, removing the checksum check now it works!
Thanks a lot :-)
Perhaps write few words in the doc about this behavior...
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)