2019-08-31, 02:05 AM
Hi, I also got an error when trying to upgrade from 1.0-1.2
Error code is :
UPDATING PACKAGES...
Reading package lists... Done
Building dependency tree
Reading state information... Done
Calculating upgrade... Done
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
1 not fully installed or removed.
After this operation, 0 B of additional disk space will be used.
Setting up hostapd (2:2.6-21~bpo9~rpt1) ...
Job for hostapd.service failed because the control process exited with error code.
See "systemctl status hostapd.service" and "journalctl -xe" for details.
invoke-rc.d: initscript hostapd, action "restart" failed.
* hostapd.service - Advanced IEEE 802.11 AP and IEEE 802.1X/WPA/WPA2/EAP Authenticator
Loaded: loaded (/lib/systemd/system/hostapd.service; disabled; vendor preset: enabled)
Active: activating (auto-restart) (Result: exit-code) since Sat 2019-08-31 10:27:38 AEST; 44ms ago
Process: 1642 ExecStart=/usr/sbin/hostapd -P /run/hostapd.pid -B $DAEMON_OPTS ${DAEMON_CONF} (code=exited, status=1/FAILURE)
Aug 31 10:27:38 openplotter systemd[1]: hostapd.service: Unit entered failedâ¦te.
Aug 31 10:27:38 openplotter systemd[1]: hostapd.service: Failed with result â¦e'.
Hint: Some lines were ellipsized, use -l to show in full.
dpkg: error processing package hostapd (--configure):
subprocess installed post-installation script returned error exit status 1
Errors were encountered while processing:
hostapd
E: Sub-process /usr/bin/dpkg returned an error code (1)
#### ERROR. ABORTING, PRESS ENTER TO EXIT ####
I'm not sure if it has anything to do with it, however my HDMI port is playing up.
I've tried adjusting the HDMI settings as found on other forums, and basically it hasn't worked in a week. I connect via VNC server, however I came down today to see the HDMI working, however it went off for a while, now back on...currently using.
Any ideas on above upgrade error, and if it could have anything to do with HDMI output?
Thanks
Error code is :
UPDATING PACKAGES...
Reading package lists... Done
Building dependency tree
Reading state information... Done
Calculating upgrade... Done
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
1 not fully installed or removed.
After this operation, 0 B of additional disk space will be used.
Setting up hostapd (2:2.6-21~bpo9~rpt1) ...
Job for hostapd.service failed because the control process exited with error code.
See "systemctl status hostapd.service" and "journalctl -xe" for details.
invoke-rc.d: initscript hostapd, action "restart" failed.
* hostapd.service - Advanced IEEE 802.11 AP and IEEE 802.1X/WPA/WPA2/EAP Authenticator
Loaded: loaded (/lib/systemd/system/hostapd.service; disabled; vendor preset: enabled)
Active: activating (auto-restart) (Result: exit-code) since Sat 2019-08-31 10:27:38 AEST; 44ms ago
Process: 1642 ExecStart=/usr/sbin/hostapd -P /run/hostapd.pid -B $DAEMON_OPTS ${DAEMON_CONF} (code=exited, status=1/FAILURE)
Aug 31 10:27:38 openplotter systemd[1]: hostapd.service: Unit entered failedâ¦te.
Aug 31 10:27:38 openplotter systemd[1]: hostapd.service: Failed with result â¦e'.
Hint: Some lines were ellipsized, use -l to show in full.
dpkg: error processing package hostapd (--configure):
subprocess installed post-installation script returned error exit status 1
Errors were encountered while processing:
hostapd
E: Sub-process /usr/bin/dpkg returned an error code (1)
#### ERROR. ABORTING, PRESS ENTER TO EXIT ####
I'm not sure if it has anything to do with it, however my HDMI port is playing up.
I've tried adjusting the HDMI settings as found on other forums, and basically it hasn't worked in a week. I connect via VNC server, however I came down today to see the HDMI working, however it went off for a while, now back on...currently using.
Any ideas on above upgrade error, and if it could have anything to do with HDMI output?
Thanks