Still issues, with GPIO, I2C inputs and Analog ads1115 not starting with OP

[Alpenskipper]

Hi,

I have still issues, with GPIO and I2C inputs and Analog ads1115 not starting with OP.

System: OP 0.16 fresh install, RP 3, no Errors in debug mode, tried autostart latency of 60 sec, no success.

When restarting GPIOs and Analog ads1115 manualy, everything is fine.

Martin




[GENERAL]
version = 0.16.0
state = beta
lang = de
repository = openplotter
op_folder = /.config

[AIS-SDR]
enable = 0
gain = 
ppm = 
channel = a
band = 
gsm_channel = 

[NMEA0183]
sentences = 

[STARTUP]
delay = 30
opencpn = 0
opencpn_no_opengl = 0
opencpn_fullscreen = 1
kplex = 1
x11vnc = 1
vnc_pass = 1
gps_time = 1
maximize = 1
play = 1
sound = /home/pi/.config/openplotter/sounds/Store_Door_Chime.mp3
node_red = 1

[CALCULATE]
nmea_rate_cal = 1
cal_accuracy = 1
nmea_mag_var = 0
nmea_hdt = 0
nmea_rot = 0
tw_stw = 0
tw_sog = 0
mag_var = 
hdt = 
hdt_dev = 
rot = 

[N2K]
enable = 0
can_usb = /dev/ttyOP_nmea
pgn_output = 
pgn_generate = 
output = 0

[WIFI]
enable = 1
ip = 192.168.5.1
device = wlan0
share = wlan2
ssid = Bordnetz
password = ***
hw_mode = g
channel = 1
wpa = 2
bridge = 0

[GPIO]
sensors = [['AC', 'in', '12', 'down'], ['motion', 'in', '17', 'down'], ['bilgeunten', 'in', '20', 'up'], ['bilgeoben', 'in', '21', 'up']]

[TWITTER]
enable = 0
apikey = 
apisecret = 
accesstoken = 
accesstokensecret = 

[GMAIL]
enable = 1
gmail = ***
password = ***
recipient = trigger@applet.ifttt.com

[ACTIONS]
triggers = [[0, 'sensors.AC.value', 2, '0', [['ACT14', '#ACoff', 3.0, 3], ['ACT15', '/home/pi/.config/openplotter/sounds/Schiffshorn-eines-grossen.mp3', 0.0, 0]]], [0, 'sensors.AC.value', 2, '1', [['ACT14', '#ACon', 0.0, 0], ['ACT15', '/home/pi/.config/openplotter/sounds/Klingel-ding-dong.mp3', 0.0, 0]]], [0, 'sensors.motion.value', 2, '1', [['ACT14', '#motion', 0.0, 0], ['ACT15', '/home/pi/.config/openplotter/sounds/Polizeisirene-martinshorn-6.mp3', 0.0, 0]]], [0, 'environment.inside.humidity.value', 5, '0', [['ACT14', '#IT\n<environment.inside.temperature>\n', 12.0, 3], ['ACT14', '#HUM\n<environment.inside.humidity>', 12.0, 3], ['ACT14', 'Test', 3.0, 3]]], [0, -1, 6, '2017-08-28T20:00:00', [['MQTTAC', '<sensors.AC>', 600.0, 1], ['MQTTmotion', '<sensors.motion>', 600.0, 1], ['MQTTIT', '<environment.inside.temperature>', 600.0, 1], ['MQTTHUM', '<environment.inside.humidity>', 600.0, 1], ['MQTTDC', '<electrical.batteries.service.voltage>', 600.0, 1], ['MQTTbilgeunten', '<sensors.bilgeunten>', 600.0, 1], ['MQTTbilgeoben', '<sensors.bilgeoben>', 600.0, 1]]], [0, 'sensors.bilgeunten.value', 2, '0', [['ACT15', '/home/pi/.config/openplotter/sounds/Smoke_Alarm.mp3', 0.0, 0], ['MQTTbilgeunten', '#bilgeuntenwasser', 0.0, 0], ['ACT14', '#bilgeuntenwasser', 0.0, 0]]], [0, 'sensors.bilgeunten.value', 2, '1', [['MQTTbilgeunten', '#bilgeuntentrocken', 0.0, 0]]], [0, 'sensors.bilgeoben.value', 2, '0', [['ACT15', '/home/pi/.config/openplotter/sounds/Smoke_Alarm.mp3', 0.0, 0], ['MQTTbilgeoben', '#bilgeobenwasser', 0.0, 0], ['ACT14', '#bilgeobenwasser', 0.0, 0]]], [0, 'sensors.bilgeoben.value', 2, '1', [['MQTTbilgeoben', '#bilgeobentrocken', 0.0, 0]]]]

[1W]
ds18b20 = 

[UDEV]
usbinst = [['ttyOP_nmea', '1a86', '7523', '', '1-1.4.3:1.0', 'dev', 'ttyUSB'], ['ttyOP_gps', '1546', '01a7', '', '1-1.4.4.4:1.0', 'dev', 'ttyACM']]

[SMS]
enable = 0
serial = /dev/ttyUSB0
bluetooth = 
connection = at19200
enable_sending = 0
phone = 

[MQTT]
broker = m12.cloudmqtt.com
port = 18676
username = xwbvgase
password = ***
topics = [[u'kaethe', 0, ''], [u'AC', 0, ''], [u'motion', 0, ''], [u'IT', 0, ''], [u'HUM', 0, ''], [u'DC', 0, ''], [u'bilgeunten', 0, ''], [u'bilgeoben', 0, '']]

[OFFSET]
heel = 0.0
pitch = 0.0
heading = 0.0
pressure = 1.04639
temperature_p = 0.108558
humidity = 0.0
temperature_h = 0.0

[I2C]
sk_hdg = 0
sk_heel = 0
sk_pitch = 0
sk_press = 0
sk_temp_p = 0
sk_hum = 0
sk_temp_h = 0
p_temp_skt = 
hum_skt = 
h_temp_skt = 
rate_imu = 1
rate_press = 1
rate_hum = 1
sensors = [['BMP180', 'rtimulib.press.2.0x77', [['environment.outside.pressure', 5.0, 0.0], ['environment.inside.temperature', 5.0, 0.0]]], ['HTU21D', 'rtimulib.hum.3.0x40', [['environment.inside.humidity', 5.0, 0.0], ['environment.outside.temperature', 5.0, 0.0]]]]

[SPI]
mcp = [[0, 0, '', '', 0], [0, 1, '', '', 0], [0, 2, '', '', 0], [0, 3, '', '', 0], [0, 4, '', '', 0], [0, 5, '', '', 0], [0, 6, '', '', 0], [0, 7, '', '', 0]]

[TOOLS]
py = [['Analog ads1115', 'put analog values to SignalK', 'analog_ads1115.py', '1'], ['Analog Firmata', 'put analog values to SignalK', 'oppymata.py', '0'], ['SignalK Simulator', 'change values with sliders and send values to SignalK', 'SK-simulator.py', '0'], ['Auto Setup', 'configure basic system', 'autosetup_tty.py', '0']]

[COMPASS]
magnetic_h = 
heel = 
pitch = 
rate = 
deviation = [[0, 0], [10, 10], [20, 20], [30, 30], [40, 40], [50, 50], [60, 60], [70, 70], [80, 80], [90, 90], [100, 100], [110, 110], [120, 120], [130, 130], [140, 140], [150, 150], [160, 160], [170, 170], [180, 180], [190, 190], [200, 200], [210, 210], [220, 220], [230, 230], [240, 240], [250, 250], [260, 260], [270, 270], [280, 280], [290, 290], [300, 300], [310, 310], [320, 320], [330, 330], [340, 340], [350, 350], [360, 360]]
variation =