This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.
OpenMarine › OpenPlotter › General discussion v
Server Hardware for openplotter?

Thread Rating:
  • 2 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Server Hardware for openplotter?
glowntiger Offline
Member
***
Posts: 181
Threads: 4
Joined: May 2018
Reputation: 28
#191
2020-04-16, 07:28 AM
Hi,
all ordered packages are on their way. Sorry for the delay.
Now are enough in stock... ;-)

@max:
I send it to you next time... ;-)
Find
Reply
Max1947 Offline
Senior Member
****
Posts: 322
Threads: 23
Joined: Apr 2019
Reputation: 6
#192
2020-04-16, 12:48 PM
Ok Thomas, thanks!

For Italian users I attach the translated QuickGuide. Good wind and stay at home again ... we will make beautiful sailing before long!  Big Grin

(Ok Thomas, grazie!

Per gli utenti italiani allego la QuickGuide tradotta. Buon vento e restate in casa ancora...faremo belle veleggiate fra non molto!)  Shy


Attached Files
.pdf   QuickGuide_MCS.en.it.pdf (Size: 1.78 MB / Downloads: 187)
Website Find
Reply
Max1947 Offline
Senior Member
****
Posts: 322
Threads: 23
Joined: Apr 2019
Reputation: 6
#193
2020-04-22, 10:08 PM
Hi Thomas, the new card has arrived, thank you. I connected the Clipper Wind, the led on the MCS is steady red (does not flash). Notify me when you want to connect with anidesk for posting.  Smile
Website Find
Reply
Bill_ Maxwell Offline
Junior Member
**
Posts: 21
Threads: 2
Joined: Feb 2019
Reputation: 0
#194
2020-04-22, 11:29 PM
Hi Thomas
Are you able to send the server board to Australia yet?
Bill
Find
Reply
glowntiger Offline
Member
***
Posts: 181
Threads: 4
Joined: May 2018
Reputation: 28
#195
2020-04-23, 08:07 AM
Hi Bill,
i have add Australia (Australien in German) to the shipping targets on the website.
Shipping cost is a little bit higher... :-( (48€)
Don´t know how long the shipping needs in the Moment. I send out parts in 1-2 days...
Find
Reply
Bill_ Maxwell Offline
Junior Member
**
Posts: 21
Threads: 2
Joined: Feb 2019
Reputation: 0
#196
2020-04-23, 11:02 AM
Viele Danke, Thomas.
Find
Reply
Max1947 Offline
Senior Member
****
Posts: 322
Threads: 23
Joined: Apr 2019
Reputation: 6
#197
2020-04-23, 01:30 PM
Ok Thomas, thanks for your work. Now everything works perfectly. I hope the SignalK managers will make the adjustment after your request. Good wind to you and the whole OP group! Smile
Website Find
Reply
flybob Offline
Pro Sailor
**
Posts: 42
Threads: 3
Joined: Nov 2019
Reputation: 4
#198
2020-04-23, 07:30 PM
I got the board yesterday, finally! Mounted in in the boat and tried to boot up - nothing. However seems like the ribbon cable was a bit loose which was fixed at home later. So now it's booting and should work just fine.

However - the Moitessier hat cannot be mounted without an extra pin head and it's quite tricky to come by actually! Not a lot of places ship to Sweden these days so I've been hunting online for a couple of hours(!) for something as simple as a gpio duplicator with reasonable shipping time. Would be a great accessory to your shop glowntiger Wink
Jeanneau Sun Odyssey 42.2 - All Openplottered and hooked up on online.
Find
Reply
Max1947 Offline
Senior Member
****
Posts: 322
Threads: 23
Joined: Apr 2019
Reputation: 6
#199
2020-04-23, 08:03 PM
(2020-04-23, 07:30 PM)flybob Wrote: I got the board yesterday, finally! Mounted in in the boat and tried to boot up - nothing. However seems like the ribbon cable was a bit loose which was fixed at home later. So now it's booting and should work just fine.

However - the Moitessier hat cannot be mounted without an extra pin head and it's quite tricky to come by actually! Not a lot of places ship to Sweden these days so I've been hunting online for a couple of hours(!) for something as simple as a gpio duplicator with reasonable shipping time. Would be a great accessory to your shop glowntiger Wink

Hi, is this what you are looking for? https://www.amazon.com/Connectors-Raspbe...09&sr=8-51

However Thomas should have them!  Smile
Website Find
Reply
jamieFL Offline
Member
***
Posts: 68
Threads: 11
Joined: Apr 2020
Reputation: 2
#200
2020-04-25, 12:30 PM
Please forgive me. I've reviewed the first few and last few pages and this looks very promising. Can the OP please update the first post, or provide a link to where the most up-to-date information about this project seen.
Find
Reply


Forum Jump:


Users browsing this thread: 4 Guest(s)