Hi,
I'm about to give up... I've been trying to install the V3 version on a raspberry 4B 8 gig ram with a moitessier HAT
Files I used:
2022-07-18-OpenPlotter-v3-Starting-stable-64bit.img but there is no md5sum to check it
After booting, I run
Now Open plotter is booting and I'm able to check the config:
So far so good but When I tried to install the driver of the moitessier HAT with this file moitessier_1.20220328_bullseye_5.15.30_3.0.0_armhf.deb from here
https://www.rooco.eu/2018/06/13/firmware...ssier-hat/
with this command
And I get this message:
Anybody has an idea why the driver fail to install?
Thanks ya all.
I'm about to give up... I've been trying to install the V3 version on a raspberry 4B 8 gig ram with a moitessier HAT
Files I used:
2022-07-18-OpenPlotter-v3-Starting-stable-64bit.img but there is no md5sum to check it
After booting, I run
Code:
apt-get update
apt-get upgrade
Now Open plotter is booting and I'm able to check the config:
Code:
Checking NTP server... | not running
Checking Power off management... | disabled
Checking Shutdown management... | disabled
Checking OpenPlotter autostart... | enabled
Checking rescue mode... | disabled
Checking debugging mode... | disabled
Checking system log file size... | System log file size: 1.02 MB
Checking OpenPlotter packages source... | added
Checking serial connections alias... | All your serial connections have an assigned alias
Checking OpenCPN... | not running | autostart disabled
Checking Signal K server... | running
Checking serial connections conflicts... | no conflicts
Checking network connections conflicts... | no conflicts
Checking GPIO conflicts... | no conflicts
CHECK SYSTEM FINISHED
So far so good but When I tried to install the driver of the moitessier HAT with this file moitessier_1.20220328_bullseye_5.15.30_3.0.0_armhf.deb from here
https://www.rooco.eu/2018/06/13/firmware...ssier-hat/
with this command
Code:
root@plotter-1:~# dpkg -i /root/moitessier_1.20220328_bullseye_5.15.30_3.0.0_armhf.deb
And I get this message:
Code:
root@plotter-1:/var/log# dpkg -i /root/moitessier_1.20220328_bullseye_5.15.30_3.0.0_armhf.deb
Selecting previously unselected package moitessier:armhf.
(Reading database ... 95377 files and directories currently installed.)
Preparing to unpack .../moitessier_1.20220328_bullseye_5.15.30_3.0.0_armhf.deb ...
Unpacking moitessier:armhf (3.0.0) ...
Setting up moitessier:armhf (3.0.0) ...
******************************************************************************************
Running post install...
******************************************************************************************
/etc/systemd/system/moitessier.shutdown.service
[Unit]
Description=Moitessier Shutdown
[Service]
ExecStart=/home/pi/moitessier/scripts/system_shutdown
Restart=always
[Install]
WantedBy=multi-user.target
******************************************************************************************
Setting up interfaces...
******************************************************************************************
moitessier: setting up /etc/modules
i2c-dev
******************************************************************************************
Updating HAT firmware...
******************************************************************************************
******************************************************************************************
This script is used to flash the STM32 microcontroller on the Moitessier HAT.
One of the following options can be applied:
-r : Will load the latest firmware release from the remote repository https://github.com/mr-rooney/moitessier-firmware.git.
The firmware will be located in "./fw/application.binary".
-s : Specifies the firmware that should be used.
This option requires the path + filename as parameter
-f : Forces the Raspberry Pi to shutdown after firmware update. A shutdown + power cycle
is required only for virgin Moitessier HATs without any firmware.
Note: Options -s and -r must not be applied at the same time!!
******************************************************************************************
******************************************************************************************
Determining I2C GPIO device
******************************************************************************************
******************************************************************************************
I2C GPIO device: 3
******************************************************************************************
******************************************************************************************
The firmware file "application.binary" is used for the update
******************************************************************************************
******************************************************************************************
Terminating running processes...
******************************************************************************************
******************************************************************************************
"kplex" not running
******************************************************************************************
******************************************************************************************
"gpsd" not running
******************************************************************************************
******************************************************************************************
"opencpn" not running
******************************************************************************************
******************************************************************************************
"node" killed
******************************************************************************************
...................................
******************************************************************************************
Flashing firmware.
******************************************************************************************
******************************************************************************************
ERROR occured!!
File ./stm32flash_5.15.32-v8+ does not exist
******************************************************************************************
******************************************************************************************
ERROR occured!!
Flashing firmware failed.
******************************************************************************************
******************************************************************************************
ERROR occured!!
An error occured, we will retry.
******************************************************************************************
******************************************************************************************
Terminating running processes...
******************************************************************************************
******************************************************************************************
"kplex" not running
******************************************************************************************
******************************************************************************************
"gpsd" not running
******************************************************************************************
******************************************************************************************
"opencpn" not running
******************************************************************************************
******************************************************************************************
"node" killed
******************************************************************************************
......................................
******************************************************************************************
Flashing firmware.
******************************************************************************************
******************************************************************************************
ERROR occured!!
File ./stm32flash_5.15.32-v8+ does not exist
******************************************************************************************
******************************************************************************************
ERROR occured!!
Flashing firmware failed.
******************************************************************************************
******************************************************************************************
ERROR occured!!
An error occured, we will retry.
******************************************************************************************
******************************************************************************************
Terminating running processes...
******************************************************************************************
******************************************************************************************
"kplex" not running
******************************************************************************************
******************************************************************************************
"gpsd" not running
******************************************************************************************
******************************************************************************************
"opencpn" not running
******************************************************************************************
******************************************************************************************
"node" killed
******************************************************************************************
.......................................
******************************************************************************************
Flashing firmware.
******************************************************************************************
******************************************************************************************
ERROR occured!!
File ./stm32flash_5.15.32-v8+ does not exist
******************************************************************************************
******************************************************************************************
ERROR occured!!
Flashing firmware failed.
******************************************************************************************
******************************************************************************************
ERROR occured!!
An error occured, we will retry.
******************************************************************************************
******************************************************************************************
Terminating running processes...
******************************************************************************************
******************************************************************************************
"kplex" not running
******************************************************************************************
******************************************************************************************
"gpsd" not running
******************************************************************************************
******************************************************************************************
"opencpn" not running
******************************************************************************************
******************************************************************************************
"node" killed
******************************************************************************************
.....................................
******************************************************************************************
Flashing firmware.
******************************************************************************************
******************************************************************************************
ERROR occured!!
File ./stm32flash_5.15.32-v8+ does not exist
******************************************************************************************
******************************************************************************************
ERROR occured!!
Flashing firmware failed.
******************************************************************************************
******************************************************************************************
ERROR occured!!
An error occured, we will retry.
******************************************************************************************
******************************************************************************************
Terminating running processes...
******************************************************************************************
******************************************************************************************
"kplex" not running
******************************************************************************************
******************************************************************************************
"gpsd" not running
******************************************************************************************
******************************************************************************************
"opencpn" not running
******************************************************************************************
******************************************************************************************
"node" killed
******************************************************************************************
.......................................
******************************************************************************************
Flashing firmware.
******************************************************************************************
******************************************************************************************
ERROR occured!!
File ./stm32flash_5.15.32-v8+ does not exist
******************************************************************************************
******************************************************************************************
ERROR occured!!
Flashing firmware failed.
******************************************************************************************
******************************************************************************************
ERROR occured!!
An error occured, we will retry.
******************************************************************************************
******************************************************************************************
ERROR occured!!
FIRMWARE UPDATE FAILED!!!
******************************************************************************************
******************************************************************************************
ERROR occured!!
You might try to install the package again.
******************************************************************************************
dpkg: error processing package moitessier:armhf (--install):
installed moitessier:armhf package post-installation script subprocess returned error exit status 1
Errors were encountered while processing:
moitessier:armhf
root@plotter-1:/var/log#
Anybody has an idea why the driver fail to install?
Thanks ya all.