2018-09-22, 01:18 AM
Pages: 1 2
2018-09-22, 12:09 PM
ok. what other rows I need to comment? Row number 1225 didn't resolve problem, LCD doesn't works.
2018-09-22, 02:13 PM
Just keep commenting out whatever lines throw exceptions from client.py until it works. Basically anything with glut. This must be a new version of glut because it never caused problems before.
The lcd wasn't really intended for use with openplotter, but it is of course possible. I will correct it for the next version.
The lcd wasn't really intended for use with openplotter, but it is of course possible. I will correct it for the next version.
2018-09-22, 07:59 PM
(2018-09-22, 02:13 PM)seandepagnier Wrote: [ -> ]Just keep commenting out whatever lines throw exceptions from client.py until it works. Basically anything with glut. This must be a new version of glut because it never caused problems before.
The lcd wasn't really intended for use with openplotter, but it is of course possible. I will correct it for the next version.
thank you, I'll wait your updates, I think that LCD is good solution for using on the vessel.
2018-09-22, 08:49 PM
If you upgrade pypilot from git, the problem is fixed.
2018-09-22, 10:24 PM
(2018-09-22, 08:49 PM)seandepagnier Wrote: [ -> ]If you upgrade pypilot from git, the problem is fixed.
thank you! I made next steps for recover this problem:
cd
git clone https://github.com/pypilot/pypilot
git clone https://github.com/pypilot/pypilot_data
cp -rv pypilot_data/* pypilot
cd pypilot
sudo python setup.py build
sudo python setup.py install
and finaly
pypilot_lcdclient nokia5110
LCD works coorectly!
thank you very much!
2018-09-27, 08:28 PM
one more question. How to connect lirc to lcd?
software lirc has been installed and configured. but I can't to make communication between lcd and remote control/ how to do it?
software lirc has been installed and configured. but I can't to make communication between lcd and remote control/ how to do it?
2018-09-28, 01:31 AM
http://pypilot.org/wiki/doku.php?id=programming_remotes
The instructions are for tinypilot, you will have to adapt for openplotter.
The instructions are for tinypilot, you will have to adapt for openplotter.
2018-09-28, 07:23 AM
(2018-09-28, 01:31 AM)seandepagnier Wrote: [ -> ]http://pypilot.org/wiki/doku.php?id=programming_remotesI made as here has been written. Lirc service is started successfull, irw shows right but pypilot doesn't communicate with lirc:
The instructions are for tinypilot, you will have to adapt for openplotter.
pi@openplotter:~ $ pypilot_lcdclient nokia5110
have gpio for raspberry pi
no lirc available
init...
using nokia511
e.t.c.
how to repair this one?
2018-10-01, 09:01 PM
I made next steps:
>sudo apt install python-lirc python-pylirc
afer that I see:
pi@openplotter:~ $ pypilot_lcdclient nokia5110
have gpio for raspberry pi
have lirc for remote control
init...
using nokia5110
loading load config file: /home/pi/.pypilot/lcdclient.conf
failed to load config file: /home/pi/.pypilot/lcdclient.conf
pypilot: could not open config files /home/pi/.lircrc and /etc/lirc/lircrc
pypilot: No such file or directory
failed to initialize lirc. is .lircrc missing?
connected
but pressing to any key doesdn't make results. Nothing effect.
software irw shows successful recognizing remote control's keys:
pi@openplotter:~ $ irw
0000000008f7807f 00 KEY_POWER remote
0000000008f700ff 00 KEY_SELECT remote
0000000008f740bf 00 KEY_MUTE remote
0000000008f7708f 00 KEY_RIGHT remote
0000000008f748b7 00 KEY_LEFT remote
0000000008f78877 00 KEY_UP remote
0000000008f7a857 00 KEY_DOWN remote
where is my mistake?
>sudo apt install python-lirc python-pylirc
afer that I see:
pi@openplotter:~ $ pypilot_lcdclient nokia5110
have gpio for raspberry pi
have lirc for remote control
init...
using nokia5110
loading load config file: /home/pi/.pypilot/lcdclient.conf
failed to load config file: /home/pi/.pypilot/lcdclient.conf
pypilot: could not open config files /home/pi/.lircrc and /etc/lirc/lircrc
pypilot: No such file or directory
failed to initialize lirc. is .lircrc missing?
connected
but pressing to any key doesdn't make results. Nothing effect.
software irw shows successful recognizing remote control's keys:
pi@openplotter:~ $ irw
0000000008f7807f 00 KEY_POWER remote
0000000008f700ff 00 KEY_SELECT remote
0000000008f740bf 00 KEY_MUTE remote
0000000008f7708f 00 KEY_RIGHT remote
0000000008f748b7 00 KEY_LEFT remote
0000000008f78877 00 KEY_UP remote
0000000008f7a857 00 KEY_DOWN remote
where is my mistake?
Pages: 1 2