Connect autohelm to op - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: Connect autohelm to op (/showthread.php?tid=2361) |
Connect autohelm to op - luchin0 - 2020-02-22 Last year i successfully installed op in my boat. It gives me a optimum support during my navigation in the north adriac see. Now i would like to implement my configuration connecting my autohelm to op, basically for the batimetric and wind misure. I have the instrument panel and the plug as show below... Sameone can explain in a simple way how can i connect them to op? Thank you for all your help and support Inviato dal mio ANE-LX2 utilizzando Tapatalk RE: Connect autohelm to op - beholder77 - 2020-02-22 Unfortunately ST50 TRIDATA and ST50 Wind instrument has no NMEA 0183 interface for connecting third party equipment (only ST50+ TRIDATA REPEATER and Autohelm MFD has it). Tridata and Wind displays only has Seatalk interface (3pin connector on your picture) You need some kind of Seatalk->NMEA 0183 converter, for example Raymarine "PC/Seatalk/NMEA Interface BOX" (some call it RS232 BOX) which is hard to find and not so cheap (for my taste) PS: I see second seatalk cable on your picture (from wind instrument) which is leading to some another place. It is just power or i guess you have at least one another device in your seatalk network. What is it? Is it Repeater? Connect autohelm to op - luchin0 - 2020-02-23 Thank you. This one can make the work? https://www.painestore.it/convertitore_stng/nmea0183_cod_e70196?gclid=Cj0KCQiA4sjyBRC5ARIsAEHsELFwwdGPiaao7eAGbZ330QSheADcdVTh3tTivU_3lJiN0JutqblJpiwaAvvMEALw_wcB Something cheaper exists? I though it was 1 camble for wind and 1 for depth... But i never check. Next time i will Inviato dal mio ANE-LX2 utilizzando Tapatalk Connect autohelm to op - abarrow - 2020-02-23 That device is for Seatalk NG. The instruments you showed use first generation Seatalk. You need a two way Seatalk bridge. Sent from my CLT-L04 using Tapatalk RE: Connect autohelm to op - Max1947 - 2020-02-23 (2020-02-23, 12:11 PM)luchin0 Wrote: Thank you. Hi, you should use this. It's also cheap ... good wind! Http: //yakbitz.com/ST1toNMEA.aspx Connect autohelm to op - luchin0 - 2020-02-23 Thank you for your suggestion. How i connect it to my rpi with moittesier hat? Difference with this one? https://www.ebay.it/itm/SEAYAK-Seatalk1-to-NMEA-USB-Converter-/173224200076 Inviato dal mio ANE-LX2 utilizzando Tapatalk RE: Connect autohelm to op - Max1947 - 2020-02-23 (2020-02-23, 04:49 PM)luchin0 Wrote: Thank you for your suggestion. Hi, it's the same I indicated. It comes from Australia (it will take some time, but the seller is serious). You must connect the output of your instruments (identifying the three corresponding colors: red + black mass or gnd- yellow Seatalk data) to the "Seyak" and connect it with the cable in dodation to a USB port of the rpi. Good job Connect autohelm to op - Techstyle - 2020-02-23 Is that device bi-directional? RE: Connect autohelm to op - Max1947 - 2020-02-24 (2020-02-23, 10:39 PM)Techstyle Wrote: Is that device bi-directional? No.! RE: Connect autohelm to op - gypsylyon - 2020-02-25 (2020-02-24, 10:26 AM)Max1947 Wrote:Full dupplex with conversion all navi standard ( nmea183, NMEA2000 and SeaTalk) are this(2020-02-23, 10:39 PM)Techstyle Wrote: Is that device bi-directional? https://ocenav.com/en/home/ That's the one I have on my boat. I have the same ST50 system Gesendet von meinem CLT-L29 mit Tapatalk |