2016-05-18, 06:48 PM
(This post was last modified: 2016-05-18, 06:53 PM by robbiedeloose.)
Hi,
I'm using a ShipModul MiniPlex-42USB to combine my nmea183 data. Untill now I connected out-1 to a serial to usb convertor to get the data to the raspberry.
I saw somebody else was trying to connect a shipmodul multiplexer (altough a never version if i'm remembering correctly) in the cruiserforum thread. This was before the usb manager was in place and I don't think it was mentioned again in that thread.
So, here it goes:
Miniplex is getting data on channel 1 from a laptop running VDRplayer and outputting that on the serial port.
Miniplex is recognised by raspbian
The usb manager recognises the usb device as well.
When I open Inspector, no nmea183 data is shown.
any ideas?
I'm using a ShipModul MiniPlex-42USB to combine my nmea183 data. Untill now I connected out-1 to a serial to usb convertor to get the data to the raspberry.
I saw somebody else was trying to connect a shipmodul multiplexer (altough a never version if i'm remembering correctly) in the cruiserforum thread. This was before the usb manager was in place and I don't think it was mentioned again in that thread.
So, here it goes:
Miniplex is getting data on channel 1 from a laptop running VDRplayer and outputting that on the serial port.
Miniplex is recognised by raspbian
Code:
pi@openplotter:~ $ lsusb
Bus 001 Device 008: ID 046d:c326 Logitech, Inc.
Bus 001 Device 007: ID 05ac:921b Apple, Inc.
Bus 001 Device 006: ID 046d:c52e Logitech, Inc.
Bus 001 Device 005: ID 05ac:911b Apple, Inc.
Bus 001 Device 004: ID 0403:fd49 Future Technology Devices International, Ltd ShipModul MiniPlex-4xUSB-AIS NMEA Multiplexer
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
pi@openplotter:~ $
Code:
pi@openplotter:~ $ dmesg | grep tty
[ 0.000000] Kernel command line: 8250.nr_uarts=0 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1680 bcm2708_fb.fbheight=1050 bcm2709.boardrev=0xa02082 bcm2709.serial=0x5c05c3b0 smsc95xx.macaddr=B8:27:EB:05:C3:B0 bcm2708_fb.fbswap=1 bcm2709.uart_clock=48000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[ 0.001339] console [tty1] enabled
[ 1.871184] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[ 5.533914] usb 1-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 47.055980] ttyUSB0: 6 input overrun(s)
The usb manager recognises the usb device as well.
When I open Inspector, no nmea183 data is shown.
any ideas?