2022-05-12, 09:27 AM
(This post was last modified: 2022-05-12, 09:36 AM by ALROCHARARI.)
Hello,
I'm lost trying to find what I'm doing wrong.
Let me try to explain what is my problem.
My installation:
Raspberry PI 4 Model B Rev 1.4 8GB
PICAN-M with CAN-Bus Micro-C, RS422 connector NME0183, 3A SMPS
NMEA 2000 test network
MAIANA CAN version with MAIANA base kit
My configuration:
Debian GNU/Linux 11 (bullseye) with latest patches
Architecture aarch64
openplotter-can/bionic,bionic,now 2.2.2-stable all [installed]
openplotter-dashboards/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-doc/bionic,bionic,now 2.2.1-dev all [installed]
openplotter-i2c/bionic,bionic,now 2.2.1-stable all [installed]
openplotter-maiana/bionic,bionic,now 2.1.2-stable all [installed]
openplotter-network/bionic,bionic,now 2.1.5-stable all [installed]
openplotter-opencpn-installer/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-serial/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-settings/bionic,bionic,now 2.9.1-stable all [installed]
openplotter-signalk-installer/bionic,bionic,now 2.4.2-stable all [installed]
My problem:
MAIANA device [Working correctly]
Catching GPS signal: led for GPS signal green on device when antenna correctly positionned outside
Device transmitting GPS packets on the CAN bus: packets visible when using candump in command line
CAN Bus 2.2.2 [Working correctly]
MCP2512 connection defined correctly: traffic is visible when activating the candump function.
Connection has been added as "can0" to SignalK. Tool is displaying correctly the connection identifier.
Signal K 1.42.00
"can0" connection is listed correctly with status "Connected to can0"
Parameters:
Data type: NMEA2000
Enabled: Yes
Logging: Yes
ID: can0
NMEA 2000 Source: Canbus (canboatjs)
Interface: can0
Use Can NAME in source data: Yes
Filters: No
Source Priorities Settings: Empty
No error reported
Problem:
No connection activity reported. Deltas/second is always at 0 for "defaults" and "can0"
Total sever Signal K throughput (deltas/second) is always at 0
In Signal K Instrument panel version 0.22.1 I have only 1 dash "validation. MAIANA" which is always at 0
Can you please help me?
Thanks in advance for your help.
Best regards,
Raoul
I'm lost trying to find what I'm doing wrong.
Let me try to explain what is my problem.
My installation:
Raspberry PI 4 Model B Rev 1.4 8GB
PICAN-M with CAN-Bus Micro-C, RS422 connector NME0183, 3A SMPS
NMEA 2000 test network
MAIANA CAN version with MAIANA base kit
My configuration:
Debian GNU/Linux 11 (bullseye) with latest patches
Architecture aarch64
openplotter-can/bionic,bionic,now 2.2.2-stable all [installed]
openplotter-dashboards/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-doc/bionic,bionic,now 2.2.1-dev all [installed]
openplotter-i2c/bionic,bionic,now 2.2.1-stable all [installed]
openplotter-maiana/bionic,bionic,now 2.1.2-stable all [installed]
openplotter-network/bionic,bionic,now 2.1.5-stable all [installed]
openplotter-opencpn-installer/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-serial/bionic,bionic,now 2.2.3-stable all [installed]
openplotter-settings/bionic,bionic,now 2.9.1-stable all [installed]
openplotter-signalk-installer/bionic,bionic,now 2.4.2-stable all [installed]
My problem:
MAIANA device [Working correctly]
Catching GPS signal: led for GPS signal green on device when antenna correctly positionned outside
Device transmitting GPS packets on the CAN bus: packets visible when using candump in command line
CAN Bus 2.2.2 [Working correctly]
MCP2512 connection defined correctly: traffic is visible when activating the candump function.
Connection has been added as "can0" to SignalK. Tool is displaying correctly the connection identifier.
Signal K 1.42.00
"can0" connection is listed correctly with status "Connected to can0"
Parameters:
Data type: NMEA2000
Enabled: Yes
Logging: Yes
ID: can0
NMEA 2000 Source: Canbus (canboatjs)
Interface: can0
Use Can NAME in source data: Yes
Filters: No
Source Priorities Settings: Empty
No error reported
Problem:
No connection activity reported. Deltas/second is always at 0 for "defaults" and "can0"
Total sever Signal K throughput (deltas/second) is always at 0
In Signal K Instrument panel version 0.22.1 I have only 1 dash "validation. MAIANA" which is always at 0
Can you please help me?
Thanks in advance for your help.
Best regards,
Raoul