2020-07-28, 08:09 PM
2020-07-28, 08:29 PM
Can you access the HAT after a reboot?
2020-07-28, 08:33 PM
yes,
check config results
AIS - GNSS
Device: /dev/moitessier.tty
Connection:
App = Signal K, Device = /dev/ttyOP_wind, ID = wind, Status = enabled
App = Signal K, Device = /dev/ttyOP_can, ID = can, Status = enabled
Compass - Trim - Heel
Pypilot mode: only compass
Connection: Signal K connection ID = Pypilot Signal K
Signal K to NMEA 0183 plugin: disabled
Heading conversion: disabled
Trim - Heel conversion: disabled
Pressure - Temperature
I2C - Signal K key for pressure: environment.outside.pressure
I2C - Signal K key for temperature: environment.inside.openplotter.temperature
Connection: Signal K connection ID = I2C
Signal K to NMEA 0183 plugin: disabled
Pressure conversion: disabled
check config results
AIS - GNSS
Device: /dev/moitessier.tty
Connection:
App = Signal K, Device = /dev/ttyOP_wind, ID = wind, Status = enabled
App = Signal K, Device = /dev/ttyOP_can, ID = can, Status = enabled
Compass - Trim - Heel
Pypilot mode: only compass
Connection: Signal K connection ID = Pypilot Signal K
Signal K to NMEA 0183 plugin: disabled
Heading conversion: disabled
Trim - Heel conversion: disabled
Pressure - Temperature
I2C - Signal K key for pressure: environment.outside.pressure
I2C - Signal K key for temperature: environment.inside.openplotter.temperature
Connection: Signal K connection ID = I2C
Signal K to NMEA 0183 plugin: disabled
Pressure conversion: disabled
2020-07-28, 08:43 PM
(2020-07-28, 08:29 PM)Rooco Wrote: [ -> ]Can you access the HAT after a reboot?
Yes, but yes nothing "serial":
https://i.imgur.com/1JJoeFu.png
https://i.imgur.com/9906XGR.png
https://i.imgur.com/4rqNkTQ.png
https://i.imgur.com/D8NsnDw.png
2020-07-28, 08:57 PM
no, in serial I only see the ttyAMA0, that is probably the UART
I get the i2c from the hat, only, ais and gps are undetected
I get the i2c from the hat, only, ais and gps are undetected
2020-07-29, 04:54 PM
If I cannot use the Moitessier HAT as GPS receiver with Buster and Raspi 3b or 4, What can I do ?
If it can work with usb gps receiver, what could be the recommandation ?
Then I might completely remove the Moitessier HAT since it uses power and becomes mostly useless...
If it can work with usb gps receiver, what could be the recommandation ?
Then I might completely remove the Moitessier HAT since it uses power and becomes mostly useless...
2020-07-29, 06:56 PM
Just to ensure, have you installed the following package?
https://get.rooco.tech/moitessier/buster..._armhf.deb
The error is caused if you use a wrong package.
Do the following:
wget https://get.rooco.tech/moitessier/buster..._armhf.deb
sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb
https://get.rooco.tech/moitessier/buster..._armhf.deb
The error is caused if you use a wrong package.
Do the following:
wget https://get.rooco.tech/moitessier/buster..._armhf.deb
sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb
2020-07-29, 07:20 PM
(2020-07-29, 06:56 PM)Rooco Wrote: [ -> ]Just to ensure, have you installed the following package?
https://get.rooco.tech/moitessier/buster..._armhf.deb
The error is caused if you use a wrong package.
Do the following:
wget https://get.rooco.tech/moitessier/buster..._armhf.deb
sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb
Sorry, I'm not a technician, just copy / paste. Where am I wrong?
https://i.imgur.com/EmvCz0p.png
2020-07-29, 08:10 PM
Unfortunately the forum software obviously shortens the link, so it is invalidated.
Click on the link and save the file on your Pi. Then you can skip the wget command.
Click on the link and save the file on your Pi. Then you can skip the wget command.
2020-07-29, 08:21 PM
Thanks @nebosa e @Rooco meanwhile I have another sd with 4.19.97 kernel fully functional ... the latter makes me crazy.
see: https://i.imgur.com/mP6i9t8.png
https://i.imgur.com/1JJoeFu.png
see: https://i.imgur.com/mP6i9t8.png
https://i.imgur.com/1JJoeFu.png