Opencpn not open in Openplotter 0.8.0 - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: Bug Reports (https://forum.openmarine.net/forumdisplay.php?fid=4) +--- Thread: Opencpn not open in Openplotter 0.8.0 (/showthread.php?tid=215) |
Opencpn not open in Openplotter 0.8.0 - Wailemann - 2016-11-05 Hello
- used other sd card (16Gb) and the problem continued - someone help? Tanks Edson RE: Opencpn not open in Openplotter 0.8.0 - Sailoog - 2016-11-05 (2016-11-05, 07:36 PM)Wailemann Wrote: Hello I'm afraid you are running a RP 1 instead of RP 2. Opencpn and signal k don't work on RP 1 and zero. RE: Opencpn not open in Openplotter 0.8.0 - Wailemann - 2016-11-05 Unfortunately it seems to be using an RP model 1 B + Tanks RE: Opencpn not open in Openplotter 0.8.0 - MHawk - 2017-01-15 Hello! I have the same issue than Wailemann encountered. I installed the OpenPlotter RPI v0.8.0 image on a RPi2 Model B. OpenPlotter works, but OpenCPN does not open. I also get the "Illegal instruction" when trying to run OpenCPN from the ~/.opencpn directory in terminal. Any suggestions on how to get OpenCPN to run? Thank you. Mike PS, I might add that the same SD card plugged into my RPi3 does allow me to run OpenCPN. RE: Opencpn not open in Openplotter 0.8.0 - commodore.white - 2017-01-29 Turns out there are two versions of CPU in the RasPi-2. My guess is the version of opencpn in openplotter relies on the more recent version. Transpires mine is an old version so I can't run OpenCPN on version 0.8 of openplotter either. Nevertheless, I've got version 0.8 going to the extent that kplex broadcasts the gps output from my Garmin 3 plus to my android tablet running OpenCPN. Guess I could build a version of opencpn that ran on the legacy version of my Pi but it probably makes sense to get a more recent one. Peter RE: Opencpn not open in Openplotter 0.8.0 - nadezhda - 2017-04-19 I get exactly the same problem with my Pi Zero and I therefore think the Pi Zero W will also have the same issue. This is a real shame because I wanted the extra low power consumption of the Pi Zero so i could leave it turned on and not worry about power. RE: Opencpn not open in Openplotter 0.8.0 - SkipperEarly - 2017-04-19 Why dont you just synch with github and compile on target machine? I attache instructions which I used for your convenience. RE: Opencpn not open in Openplotter 0.8.0 - nadezhda - 2017-04-19 Maybe we need to compile the OpenCPN for the ARM processor? This link may be of help. I need to get a Pi3 with internet connection to do it, download the stuff, transfer the SDHC to my Pi Zero and compile it. http://andersonsabroad.com/blog/raspberry-pi-marine-computer/step-5-install-opencpn-chartplotting-software/ RE: Opencpn not open in Openplotter 0.8.0 - Sailoog - 2017-04-19 openplotter is not supported by raspberry 1 and zero because 2 of the most important tools are not compiled for their micros, opencpn and signal k. If you want to run opencpn and signal k on raspberry 1 and zero you have to compile the sources. OpenCPN on raspberry 1 and zero are close to unusable because performance. |