problem installing moitessier firmware [closed] - Printable Version +- OpenMarine (https://forum.openmarine.net) +-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1) +--- Forum: How do I...? (https://forum.openmarine.net/forumdisplay.php?fid=3) +--- Thread: problem installing moitessier firmware [closed] (/showthread.php?tid=2795) |
RE: problem installing moitessier firmware - Max1947 - 2020-07-28 I really tried both packages, same result: https://i.imgur.com/a3u0pGc.png RE: problem installing moitessier firmware - Rooco - 2020-07-28 Can you access the HAT after a reboot? RE: problem installing moitessier firmware - opampca - 2020-07-28 yes, check config results AIS - GNSS Device: /dev/moitessier.tty Connection: App = Signal K, Device = /dev/ttyOP_wind, ID = wind, Status = enabled App = Signal K, Device = /dev/ttyOP_can, ID = can, Status = enabled Compass - Trim - Heel Pypilot mode: only compass Connection: Signal K connection ID = Pypilot Signal K Signal K to NMEA 0183 plugin: disabled Heading conversion: disabled Trim - Heel conversion: disabled Pressure - Temperature I2C - Signal K key for pressure: environment.outside.pressure I2C - Signal K key for temperature: environment.inside.openplotter.temperature Connection: Signal K connection ID = I2C Signal K to NMEA 0183 plugin: disabled Pressure conversion: disabled RE: problem installing moitessier firmware - Max1947 - 2020-07-28 (2020-07-28, 08:29 PM)Rooco Wrote: Can you access the HAT after a reboot? Yes, but yes nothing "serial": https://i.imgur.com/1JJoeFu.png https://i.imgur.com/9906XGR.png https://i.imgur.com/4rqNkTQ.png https://i.imgur.com/D8NsnDw.png RE: problem installing moitessier firmware - opampca - 2020-07-28 no, in serial I only see the ttyAMA0, that is probably the UART I get the i2c from the hat, only, ais and gps are undetected RE: problem installing moitessier firmware - opampca - 2020-07-29 If I cannot use the Moitessier HAT as GPS receiver with Buster and Raspi 3b or 4, What can I do ? If it can work with usb gps receiver, what could be the recommandation ? Then I might completely remove the Moitessier HAT since it uses power and becomes mostly useless... RE: problem installing moitessier firmware - Rooco - 2020-07-29 Just to ensure, have you installed the following package? https://get.rooco.tech/moitessier/buster/release/5.4.51/2.1.0/moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb The error is caused if you use a wrong package. Do the following: wget https://get.rooco.tech/moitessier/buster/release/5.4.51/2.1.0/moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb sudo dpkg -i moitessier_1.20200723-1_5.4.51_2.1.0_armhf.deb RE: problem installing moitessier firmware - Max1947 - 2020-07-29 (2020-07-29, 06:56 PM)Rooco Wrote: Just to ensure, have you installed the following package? Sorry, I'm not a technician, just copy / paste. Where am I wrong? https://i.imgur.com/EmvCz0p.png RE: problem installing moitessier firmware - Rooco - 2020-07-29 Unfortunately the forum software obviously shortens the link, so it is invalidated. Click on the link and save the file on your Pi. Then you can skip the wget command. RE: problem installing moitessier firmware - Max1947 - 2020-07-29 Thanks @nebosa e @Rooco meanwhile I have another sd with 4.19.97 kernel fully functional ... the latter makes me crazy. see: https://i.imgur.com/mP6i9t8.png https://i.imgur.com/1JJoeFu.png |