+- OpenMarine (https://forum.openmarine.net)
+-- Forum: OpenPlotter (https://forum.openmarine.net/forumdisplay.php?fid=1)
+--- Forum: General discussion (https://forum.openmarine.net/forumdisplay.php?fid=2)
+--- Thread: OpenPlotter 3 roadmap (/showthread.php?tid=3878)
RE: OpenPlotter 3 roadmap - Sailoog - 2022-11-25
openplotter-rtl_ais.service is created when you select AIS from SDR tools and click edit. After saving, this service is created using the settings provided. You need at least 1 SDR device to be connected to do this.
RE: OpenPlotter 3 roadmap - abarrow - 2022-11-25
Thanks. I thought I'd done all that, but clearly I didn't.
Process is running now.
RE: OpenPlotter 3 roadmap - abarrow - 2022-11-25
Hummm, not seeing any incoming data, but I can see the signals on CubicSDR.
RE: OpenPlotter 3 roadmap - Sailoog - 2022-11-25
calibration?
RE: OpenPlotter 3 roadmap - abarrow - 2022-11-26
Yes, definitely calibrated. I'll give it another shot.
RE: OpenPlotter 3 roadmap - hrios - 2022-11-26
Hi!!
Since last update (I2C sensors 3.3.5-beta) Air temperature and barometric pressure are not shown in OpenCPN dashboard.
Working fine until the update...
Regards
Update
No data from sensors in Signal K (BMP3xx & HTU21D)
Solution
I just edited each sensor and exit with ok and the scale factor decimals updated by itself and working again...
RE: OpenPlotter 3 roadmap - Max1947 - 2022-11-27
In OP3 the Moitessier update has disappeared. Rooco does not answer, is it to be thrown away? It would be a nice rip -off ...
In OP3 e' sparito l'aggiornamento di Moitessier. Rooco non risponde, e' da buttare? Sarebbe una bella fregatura...
RE: OpenPlotter 3 roadmap - Sailoog - 2022-11-27
(2022-11-26, 05:27 PM)hrios Wrote: Hi!!
Since last update (I2C sensors 3.3.5-beta) Air temperature and barometric pressure are not shown in OpenCPN dashboard.
Working fine until the update...
Regards
Update
No data from sensors in Signal K (BMP3xx & HTU21D)
Solution
I just edited each sensor and exit with ok and the scale factor decimals updated by itself and working again...
Yes, after adding the new "scaling factor" field, all configured sensors will fail until they are edited and this value is created with default values. New sensors will work without problem.
RE: OpenPlotter 3 roadmap - Sailoog - 2022-11-27
(2022-11-27, 12:20 PM)we will discuss a suitable solution. Wrote: In OP3 the Moitessier update has disappeared. Rooco does not answer, is it to be thrown away? It would be a nice rip -off ...
In OP3 e' sparito l'aggiornamento di Moitessier. Rooco non risponde, e' da buttare? Sarebbe una bella fregatura...
They finally answered: "we will discuss a suitable solution" a week ago but honestly I do not expect a fast solution.
Since they do not build drivers anymore, I have proposed one last and final driver to them to update the firmware and remove the driver requirement so we can use our Moitessier HATs reading directly from SPI, but still no response.
Leaving hundreds of users with a bricked board is unacceptable, we will find a solution whatever it is.
RE: OpenPlotter 3 roadmap - Max1947 - 2022-11-27
(2022-11-27, 12:39 PM)Sailoog Wrote:(2022-11-27, 12:20 PM)we will discuss a suitable solution. Wrote: In OP3 the Moitessier update has disappeared. Rooco does not answer, is it to be thrown away? It would be a nice rip -off ...
In OP3 e' sparito l'aggiornamento di Moitessier. Rooco non risponde, e' da buttare? Sarebbe una bella fregatura...
They finally answered: "we will discuss a suitable solution" a week ago but honestly I do not expect a fast solution.
Since they do not build drivers anymore, I have proposed one last and final driver to them to update the firmware and remove the driver requirement so we can use our Moitessier HATs reading directly from SPI, but still no response.
Leaving hundreds of users with a bricked board is unacceptable, we will find a solution whatever it is.
Ok, thanks Sailoog, we'll wait and in any case good work and good wind, always!